Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095461 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  P0335  Crankshaft Position Sensor Circuit Malfunction (NE Signal)  


DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2286 Runnable Signal Malfunction The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match. (1-trip detection logic*)
·

AM2 fuse

·

SFI system

·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, then start the engine and maintain an engine speed of 1000 rpm or more for 20 seconds or more.


P0335 Crankshaft Position Sensor Circuit Malfunction (NE Signal) The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match (1-trip detection logic*).
·

AM2 fuse

·

SFI system

·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Allow the engine to idle for 10 seconds or more.



*: Only detected while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

When the signal sent via either the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior. (A malfunction is detected after the engine switch is turned on (IG).)

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine cannot be started. However, the engine can be started after the engine switch has been turned off.


·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving:

If the following conditions are met, it can be determined that the malfunction is not in CAN communication but in the direct line (NE).
-

When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (perfect injection signal judgment) via CAN communication, causing the engine to stop cranking.

-

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, causing the engine to stop cranking.


If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in CAN communication.
-

When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

-

When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.


If the following conditions are met, it can be determined that there is a malfunction in both CAN communication and the direct line (NE).
-

When the engine switch is pressed, the engine stops cranking after 6 seconds.

-

When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.




Related Data List and Active Test Items
DTC No. Data List and Active Test
B2286
P0335
Power Source Control
·

Engine Condition


Starting Control
·

Engine Speed



WIRING DIAGRAM

C278449E28
5.063,0.771 5.458,0.979 0.396,0.208 10 false F13 5.104,0.604 5.365,0.771 0.26,0.167 10 false 10 4.167,0.917 4.625,1.177 0.458,0.26 10 false AM2 2.708,0.771 3.625,1.052 0.917,0.281 10 false from Battery 5.063,1.51 5.385,1.688 0.323,0.177 10 false F10 5.063,2.438 5.354,2.625 0.292,0.188 10 false F13 5.104,2.26 5.333,2.406 0.229,0.146 10 false 11 5.094,1.323 5.302,1.49 0.208,0.167 10 false 14 5.396,0.781 5.625,0.958 0.229,0.177 10 false +B 5.406,1.521 5.719,1.719 0.313,0.198 10 false NE 2.042,1.51 2.583,1.854 0.542,0.344 10 false NEO 2.448,1.385 3.302,1.604 0.854,0.219 10 false 30*1, 45*2 1.5,2.354 1.823,2.531 0.323,0.177 10 false A43 1.49,2.531 2.073,2.844 0.583,0.313 10 false ECM 5.063,2.99 6.573,3.51 1.51,0.521 10 false Certification ECU (Smart Key ECU Assembly) 5.406,2.469 5.563,2.667 0.156,0.198 10 false E 1.198,3.219 3.219,3.594 2.021,0.375 10 false : CAN Communication Line 3.188,2.906 4.448,3.135 1.26,0.229 10 false *1: for 2GR-FKS 3.188,3.219 4.448,3.448 1.26,0.229 10 false *2: for 1AR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.READ VALUE USING GTS (ENGINE CONDITION / ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the Engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Condition Engine state Stop or Run Stop: Engine stopped
Run: Engine running
-
Body Electrical > Power Source Control > Data List
Tester Display
Engine Condition
50003 223 15
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed 0 to 16383 rpm Fluctuates in accordance with Engine speed -
Body Electrical > Starting Control > Data List
Tester Display
Engine Speed
50003 221 8
OK:

The GTS display changes correctly in response to the engine condition.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2GR-FKS
Tester Connection Condition Specified Condition
F10-14 (NE) - A43-30 (NEO) Always Below 1 Ω
F10-14 (NE) or A43-30 (NEO) - Body ground Always 10 kΩ or higher

for 1AR-FE
Tester Connection Condition Specified Condition
F10-14 (NE) - A43-45 (NEO) Always Below 1 Ω
F10-14 (NE) or A43-45 (NEO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F10 and F13 certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the A43 ECM connector.


c.
C277840C18
1.448,0.188 1.844,0.375 0.396,0.188 0.958,1.646 1.146,1.073 false 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 1.542,0.198 1.823,0.354 0.281,0.156 10 false F10 0.875,1.667 1.156,1.885 0.281,0.219 10 false NE
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Using an oscilloscope, check the engine speed input signal waveform at the terminal of the certification ECU (smart key ECU assembly).

Standard Frequency:
Tester Connection Condition Specified Condition
F10-14 (NE) - Body ground Engine stopped No pulse generation
Engine running Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG