Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296316 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

A395927E05
6.042,2.125 6.5,2.323 0.458,0.198 10 false ECM 5.271,0.604 5.729,0.802 0.458,0.198 10 false A43 5.281,1.396 5.74,1.594 0.458,0.198 10 false A43 5.677,0.5 6.135,0.698 0.458,0.198 10 false STP 5.677,1.302 6.135,1.5 0.458,0.198 10 false ST1- 5.323,0.385 5.781,0.583 0.458,0.198 10 false 27 5.313,1.188 5.771,1.385 0.458,0.198 10 false 42 5.385,3.281 6.906,3.677 1.521,0.396 10 false Certification ECU (Smart Key ECU Assembly) 5.094,3.281 5.552,3.479 0.458,0.198 10 false F10 5.75,2.865 6.302,3.063 0.552,0.198 10 false STP1 5.563,2.76 6.021,2.958 0.458,0.198 10 false 2 2.948,4.281 5.104,4.646 2.156,0.365 10 false Transmission Floor Shift Assembly (Shift Lock Control Unit) 2.646,4.281 3.656,4.479 1.01,0.198 10 false F48 4,3.896 4.458,4.094 0.458,0.198 10 false STP 4.375,3.792 5.073,3.979 0.698,0.188 10 false 6 2.146,3.26 5,3.5 2.854,0.24 10 false Skid Control ECU (Brake Actuator Assembly) 1.823,3.25 2.281,3.448 0.458,0.198 10 false A86 3.906,2.865 4.365,3.063 0.458,0.198 10 false STP2 4.354,2.76 4.813,2.958 0.458,0.198 10 false 5 3.573,1.729 4.031,1.927 0.458,0.198 10 false GND 3.031,2.104 4.896,2.323 1.865,0.219 10 false Stop Light Switch Assembly 2.688,2.104 3.146,2.302 0.458,0.198 10 false A87 3.385,1.615 3.844,1.813 0.458,0.198 10 false 2 3.583,1.24 4.042,1.438 0.458,0.198 10 false B 3.583,0.708 4.042,0.906 0.458,0.198 10 false B 3.385,1.115 3.844,1.313 0.458,0.198 10 false 6 3.406,0.615 3.865,0.813 0.458,0.198 10 false 7 2.469,1.385 2.927,1.583 0.458,0.198 10 false IG2 2.396,0.885 2.854,1.083 0.458,0.198 10 false STOP 0.49,1.219 1.698,1.469 1.208,0.25 10 false from IG2 Relay 0.521,0.719 1.969,1.01 1.448,0.292 10 false from ALT Fuse 4.135,0.604 4.594,0.802 0.458,0.198 10 false L 4.156,1.406 4.615,1.604 0.458,0.198 10 false L 4.344,1.292 4.802,1.49 0.458,0.198 10 false 5 4.344,0.49 4.802,0.688 0.458,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
A395526C03
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.552,0.344 2.01,0.542 0.458,0.198 10 false A87
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A87 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A87-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A87-7 (B) - Body ground Always 11 to 14 V
A87-6 (B) - Body ground Engine switch on (IG) 11 to 14 V
A87-6 (B) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A43 ECM connector.


b.

Disconnect the A87 stop light switch assembly connector.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the F48 transmission floor shift assembly (shift lock control unit) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-42 (ST1-) - A87-5 (L) Always Below 1 Ω
A43-27 (STP) - A87-3 (L) Always Below 1 Ω
A43-42 (ST1-) or A87-5 (L) - Body ground Always 10 kΩ or higher
A43-27 (STP) or A87-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR