Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER HEAD › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0298900 CYLINDER HEAD A

2GR-FKS ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for bank 1 and bank 2.

·

The following procedure is for bank 2.



PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head LH to between 80 and 100°C (176 and 212°F).


b.

Place the cylinder head LH on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A366196C01
1.24,0.885 1.771,0.281 1.771,0.281 1.427,1.24 true 0.51,1.344 1.052,1.938 1.052,1.938 2.135,1.76 true 1.813,0.188 2.271,0.385 0.458,0.198 10 false SST 0.979,1.938 1.292,2.094 0.313,0.156 10 false *a
*a Wooden Block


Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A366197

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head LH.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


HINT:
·

If the intake valve guide bush bore diameter is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.

·

If the intake valve guide bush bore diameter of the cylinder head LH is more than 10.356 mm (0.40772 in.), replace the cylinder head LH.




e.

Heat the cylinder head LH to between 80 and 100°C (176 and 212°F).


f.

Place the cylinder head LH on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A366198C01
2.865,0.646 3.219,0.188 true 1.438,1.24 1.865,0.26 1.865,0.26 1.219,0.854 true 2.104,1.792 1.042,1.948 1.042,1.948 0.542,1.333 true 3.188,0.01 3.427,0.281 0.24,0.271 10 false *a 1.823,0.094 2.281,0.292 0.458,0.198 10 false SST 0.938,1.938 1.125,2.177 0.188,0.24 10 false *b
*a Protrusion Height
*b Wooden Block


Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.30 to 9.70 mm (0.366 to 0.382 in.)



h.
A366199

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head LH to between 80 and 100°C (176 and 212°F).


b.

Place the cylinder head LH on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A375155C01
2.188,1.094 2.677,0.802 2.677,0.802 2.26,0.521 true 2.719,1.896 3.042,1.896 false 3.104,1.802 3.417,1.958 0.313,0.156 10 false *a 2.719,0.719 3.177,0.917 0.458,0.198 10 false SST
*a Wooden Block


Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A366200

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head LH.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


HINT:
·

If the exhaust valve guide bush bore diameter is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.

·

If the exhaust valve guide bush bore diameter of the cylinder head LH is more than 10.356 mm (0.40772 in.), replace the cylinder head LH.




e.

Heat the cylinder head LH to between 80 and 100°C (176 and 212°F).


f.

Place the cylinder head LH on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A366201C01
0.448,1.385 0.198,0.74 true 2.188,1.115 2.896,0.854 2.896,0.854 2.271,0.542 true 2.729,1.896 2.99,1.896 false 0.094,0.552 0.406,0.708 0.313,0.156 10 false *a 2.969,0.792 3.427,0.99 0.458,0.198 10 false SST 3.063,1.813 3.375,1.969 0.313,0.156 10 false *b
*a Protrusion Height
*b Wooden Block


Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.30 to 9.70 mm (0.366 to 0.382 in.)



h.
A366202

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A366203C01
2.292,2.479 2.604,2.635 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in new ring pins to the cylinder head LH.

Standard Protrusion Height:

2.5 to 3.5 mm (0.0984 to 0.138 in.)



Hide 4.REPLACE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E6 and E8 "TORX" socket wrenches, install the stud bolts to the cylinder head LH.

A366204C01
4.938,1.51 5.26,2.01 5.26,2.01 5.594,1.49 true 4.198,3.021 4.813,3.021 true 4.188,1.365 5.26,2.458 5.26,2.458 6.146,1.323 true 1.573,1.708 1.885,2.24 1.885,2.24 2.219,1.719 true 1.688,1.188 1.885,2.229 1.885,2.229 2.146,1.188 true 5.125,0.188 5.438,0.344 0.313,0.156 10 false *a 1.813,0.177 2.125,0.333 0.313,0.156 10 false *b 3.448,1.885 3.76,2.042 0.313,0.156 10 false *c 3.417,4.583 3.729,4.74 0.313,0.156 10 false *d 3.406,5.073 3.719,5.229 0.313,0.156 10 false *e 4.167,4.833 4.479,4.99 0.313,0.156 10 false *f 5.552,4.74 5.896,5.021 0.344,0.281 10 false *g 5.563,5.115 5.875,5.271 0.313,0.156 10 false *h 6.313,4.948 6.792,5.344 0.479,0.396 10 false *i 1.177,4.313 1.604,4.656 0.427,0.344 10 false *j 1.177,5.042 1.49,5.198 0.313,0.156 10 false *k 1.969,4.656 2.448,4.896 0.479,0.24 10 false *l 0.698,5.385 0.854,5.583 0.156,0.198 10 false A 4.906,2.948 5.063,3.146 0.156,0.198 10 false C 2.938,5.375 3.094,5.573 0.156,0.198 10 false B 5.146,5.365 5.302,5.563 0.156,0.198 10 false C 5.219,2.052 5.375,2.25 0.156,0.198 10 false A 5.229,2.51 5.385,2.708 0.156,0.198 10 false B 1.823,2.281 1.979,2.479 0.156,0.198 10 false B
*a Intake Side *b Exhaust Side
*c Rear Side *d 20 mm (0.787 in.)
*e 13 mm (0.512 in.) *f 35 mm (1.38 in.)
*g 16 mm (0.630 in.) *h 9 mm (0.354 in.)
*i 27 mm (1.06 in.) *j 26 mm (1.02 in.)
*k 16.7 mm (0.657 in.) *l 51.7 mm (2.04 in.)


Torque:
Bolt (A), (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt (C) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 5.REPLACE STRAIGHT PIN

NOTICE:

If a straight pin is deformed, replace it.


a.
A366205C01
1.208,3.344 1.521,3.5 0.313,0.156 10 false *a 2.146,3.094 2.458,3.25 0.313,0.156 10 false *b
*a 34 mm (1.34 in.)
*b Protrusion Height


Using a plastic hammer, tap in new straight pins to the cylinder head LH as shown in the illustration.

Standard Protrusion Height:

17.5 to 19.5 mm (0.689 to 0.768 in.)