Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0298901 CYLINDER BLOCK A

2GR-FKS ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE STRAIGHT PIN

NOTICE:

If a straight pin is deformed, replace it.


a.

Using a plastic hammer, tap in new straight pins to the cylinder block sub-assembly.

A366509C01
1.427,1.469 1.635,1.698 true 1.24,1.594 1.75,2.052 1.75,2.052 2.313,1.51 true 4.917,1.385 5.427,1.844 5.427,1.844 5.781,1.469 true 5.594,0.688 3.979,0.979 3.979,0.979 4.479,1.448 true 4.635,4.302 5.667,4.875 5.667,4.875 5.906,3.26 true 1.031,3.74 1.823,4.823 1.823,4.823 1.219,4.188 true 2.25,3.771 1.844,4.833 1.844,4.833 2.427,4.219 true 2.021,7.073 2.156,7.438 2.156,7.438 2.323,7.063 true 1.698,0.031 2.01,0.188 0.313,0.156 10 false *a 5.25,0.042 5.563,0.198 0.313,0.156 10 false *b 1.698,2.677 2.01,2.833 0.313,0.156 10 false *c 5.271,2.781 5.583,2.938 0.313,0.156 10 false *d 1.708,5.656 2.021,5.813 0.313,0.156 10 false *e 4.063,5.469 4.375,5.625 0.313,0.156 10 false *f 5.469,5.552 5.844,5.99 0.375,0.438 10 false *g 4.844,6.667 5.156,6.823 0.313,0.156 10 false *h 6.313,6.729 6.625,6.885 0.313,0.156 10 false *i 1.677,1.688 2.052,2.115 0.375,0.427 10 false A 1.708,2.083 2.083,2.51 0.375,0.427 10 false B 5.396,1.875 5.771,2.302 0.375,0.427 10 false B 3.833,0.896 4.208,1.323 0.375,0.427 10 false C 5.677,4.917 6.052,5.344 0.375,0.427 10 false B 1.802,4.865 2.177,5.292 0.375,0.427 10 false D 4.427,6.167 4.802,6.594 0.375,0.427 10 false A 5.844,6.146 6.219,6.573 0.375,0.427 10 false B 4.406,7.5 4.594,7.781 0.188,0.281 10 false C 5.833,7.479 6.073,7.771 0.24,0.292 10 false D 2.125,7.479 2.354,7.75 0.229,0.271 10 false B
*a Front Side *b Rear Side
*c Top Side *d Bottom Side
*e RH Side *f 23 mm (0.906 in.)
*g 6 mm (0.236 in.) *h 11 mm (0.433 in.)
*i 9 mm (0.354 in.) - -


Standard Protrusion Height:
Item Specified Condition
Pin (A) 23 mm (0.906 in.)
Pin (B) 6 mm (0.236 in.)
Pin (C) 11 mm (0.433 in.)
Pin (D) 9 mm (0.354 in.)



Hide 2.REPLACE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E8 and E10 "TORX" socket wrenches, install the stud bolts to the cylinder block sub-assembly.

A399118C01
0.688,1.865 1.125,1.865 true 2.302,1.74 2.74,1.74 true 5.365,2.042 5.365,1.646 true 1.615,0.094 1.927,0.292 0.313,0.198 10 false *a 5.281,0.146 5.594,0.344 0.313,0.198 10 false *b 1.458,2.927 1.771,3.125 0.313,0.198 10 false *c 2.573,3.354 2.885,3.552 0.313,0.198 10 false *d 1.458,3.719 1.771,3.917 0.313,0.198 10 false *c 5.031,3.198 5.344,3.396 0.313,0.198 10 false *e 5.052,3.698 5.365,3.896 0.313,0.198 10 false *f 5.99,3.479 6.302,3.677 0.313,0.198 10 false *g 1.063,4.063 1.24,4.26 0.177,0.198 12 false A 4.583,4.083 4.76,4.281 0.177,0.198 12 false B 0.458,1.771 0.635,1.969 0.177,0.198 12 false A 2.813,1.635 2.99,1.833 0.177,0.198 12 false A 5.323,2.083 5.5,2.281 0.177,0.198 12 false B
*a Front Side *b LH Side
*c 12 mm (0.472 in.) *d 52 mm (2.05 in.)
*e 23 mm (0.906 in.) *f 15 mm (0.591 in.)
*g 40 mm (1.57 in.) - -


Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 3.REPLACE CONNECTING ROD SMALL END BUSH

a.
A366511N01
0.781,0.698 1.385,0.698 false 0.458,0.615 0.917,0.813 0.458,0.198 10 false SST

Using SST and a press, press out the connecting rod small end bush.

SST
09222-30010  


b.
A366512C01
2.052,1.604 2.563,1.198 2.563,1.198 2.073,0.74 true 2.646,1.135 2.958,1.292 0.313,0.156 10 false *a
*a Oil Hole


Align the oil hole of a new connecting rod small end bush with the oil hole of the connecting rod.


c.
A366511N01
0.781,0.698 1.385,0.698 false 0.458,0.615 0.917,0.813 0.458,0.198 10 false SST

Using SST and a press, install the connecting rod small end bush.

SST
09222-30010  


d.
A366514

Using a pin hole grinder, hone the connecting rod small end bush to obtain the standard oil clearance between the connecting rod small end bush and piston pin.

Standard Oil Clearance:

0.005 to 0.011 mm (0.000197 to 0.000433 in.)



e.

Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.

HINT:

Check that the piston pin fits at a normal room temperature.