Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0298901 CYLINDER BLOCK A

2GR-FKS ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 11445 1.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A370639

Remove the cylinder block water jacket spacer and cylinder block water jacket spacer LH from the cylinder block sub-assembly.


Hide 2.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.

HINT:

The matchmarks on the connecting rod sub-assembly and connecting rod cap are guides for correct reassembly.



b.
A366224C01
0,0 0,0 false
V100136

Front of Engine


Remove the 2 connecting rod bolts.


c.
A366225

Using the 2 removed connecting rod bolts, remove the connecting rod cap and lower connecting rod bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower connecting rod bearing installed to the connecting rod cap.



d.
A366226C01
0.49,0.563 1.885,0.958 true 0.302,0.458 0.615,0.615 0.313,0.156 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all of the carbon from the top of the cylinder.


e.

Push the piston, connecting rod sub-assembly and upper connecting rod bearing through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearing, connecting rod sub-assembly and connecting rod cap together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 13041 3.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rod sub-assembly and connecting rod cap.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13011 4.REMOVE PISTON RING SET

a.
A366227C01
0.719,0.521 1.479,0.521 false 0.531,0.448 0.844,0.604 0.313,0.156 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring expander and 2 side rails by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 5.REMOVE PISTON

a.
A366228

Check the fitting condition between the piston and piston pin.

i.

Try to move the piston back and forth on the piston pin.

HINT:

If abnormal movement is felt, replace the piston and piston pin as a set.




b.
A366229

Remove the connecting rod sub-assembly from the piston.

i.

Using a screwdriver, pry out the piston pin hole snap ring (front side).

NOTICE:
·

Do not remove the piston pin hole snap ring (rear side) unless it has to be replaced.

·

Be careful not to damage the piston when removing the piston pin hole snap ring (rear side).




ii.
A366230

Gradually heat the piston to approximately 80°C (176°F).

CAUTION:

Be sure to wear protective gloves.



iii.
A366231

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.





c.
A366232

Using a gasket scraper, remove any carbon from the piston top.

NOTICE:

Be careful not to scratch the piston.



d.
A366233

Using a groove cleaning tool or a broken ring, clean the piston ring grooves.


e.
A366234

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 13411 6.REMOVE CRANKSHAFT

a.
A366235N01
2.083,1.802 2.24,2 0.156,0.198 10 true 1 2.51,1.375 2.667,1.573 0.156,0.198 10 true 4 2.854,1.042 3.01,1.24 0.156,0.198 10 true 3 3.271,0.833 3.427,1.031 0.156,0.198 10 true 2 1.313,0.177 1.469,0.375 0.156,0.198 10 true 5 1.031,0.448 1.188,0.646 0.156,0.198 10 true 8 0.656,0.719 0.813,0.917 0.156,0.198 10 true 7 0.365,1.615 0.521,1.813 0.156,0.198 10 true 6

Uniformly loosen and remove the 8 crankshaft bearing cap set bolts and 8 seal washers in several steps in the order shown in the illustration.


b.
A366236N01
0.271,1.583 0.427,1.781 0.156,0.198 10 true 1 0.927,1.604 1.083,1.802 0.156,0.198 10 true 5 2.385,1.604 2.542,1.802 0.156,0.198 10 true 7 3.063,1.594 3.219,1.792 0.156,0.198 10 true 3 3.052,1.219 3.281,1.458 0.229,0.24 10 true 11 3.083,0.958 3.302,1.188 0.219,0.229 10 true 12 3.031,0.604 3.188,0.802 0.156,0.198 10 true 4 2.385,0.573 2.542,0.771 0.156,0.198 10 true 8 2.385,0.917 2.615,1.156 0.229,0.24 10 true 16 2.385,1.208 2.615,1.458 0.229,0.25 10 true 15 0.938,0.583 1.094,0.781 0.156,0.198 10 true 6 0.844,0.896 1.083,1.156 0.24,0.26 10 true 14 0.865,1.188 1.104,1.427 0.24,0.24 10 true 13 0.281,0.594 0.438,0.792 0.156,0.198 10 true 2 0.208,0.927 0.427,1.177 0.219,0.25 10 true 10 0.281,1.208 0.438,1.406 0.156,0.198 10 true 9

Uniformly loosen the 16 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.


c.
A366237C01
1.667,1.417 2.531,2.385 true 1.521,2.979 1.75,2.667 true 0.74,2.927 0.969,2.615 true 1.354,4.063 0.74,4.271 0.74,4.271 1.135,3.875 true 0.99,2.448 1.302,2.604 0.313,0.156 10 false *1 1.781,2.479 2.094,2.635 0.313,0.156 10 false *2 2.583,2.375 2.896,2.531 0.313,0.156 10 false *a 0.563,4.229 0.875,4.385 0.313,0.156 10 false *b
*1 Cylinder Block Sub-assembly
*2 Crankshaft Bearing Cap
*a Protective Tape
*b Contact Surface


Using a screwdriver with its tip wrapped with protective tape, pry out the crankshaft bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings as a set.

NOTICE:
·

Push up the crankshaft bearing cap slowly and evenly, alternating between the right and left side so that the crankshaft bearing cap can be removed.

·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and the crankshaft bearing cap.




d.

Remove the crankshaft.


Hide 11711 7.REMOVE CRANKSHAFT BEARING

a.

Remove the upper crankshaft bearings and lower crankshaft bearings.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11011 8.REMOVE CRANKSHAFT THRUST WASHER SET

a.
A366482

Remove the crankshaft thrust washer set from the cylinder block sub-assembly.


Hide 15708 9.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A366483

Using a 5 mm hexagon socket wrench, remove the 3 bolts and 3 No. 1 oil nozzle sub-assemblies.


b.

Check the 3 No. 1 oil nozzle sub-assemblies for damage or clogging.

HINT:

If there is damage or clogs, replace the No. 1 oil nozzle sub-assembly.