Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM U

2GR-FKS ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A335752E54
2.344,0.375 2.792,0.677 0.448,0.302 5.771,0.417 6.219,0.719 0.448,0.302 2.479,0.438 2.938,0.635 0.458,0.198 10 false C1 5.875,0.458 6.333,0.656 0.458,0.198 10 false A43

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A43-1 (BATT) - C1-53 (E1) GR - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A43-2 (+B) - C1-53 (E1) G - BR Power source of ECM Ignition switch ON 11 to 14 V
A43-3 (+B2) - C1-53 (E1) R - BR Power source of ECM Ignition switch ON 11 to 14 V
A43-4 (IGSW) - C1-53 (E1) W - BR Ignition switch Ignition switch ON 11 to 14 V
A43-7 (IREL) - C1-53 (E1) GR - BR INJ relay operation signal Engine stopped, ignition switch ON 0 to 1.5 V
A43-8 (+BM) - C1-53 (E1) B - BR Power source of throttle actuator Always 11 to 14 V
A43-13 (CANH) - C1-53 (E1) B - BR CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 1)
A43-14 (EC) - Body ground W-B - - Ground Always Below 1 Ω
A43-17 (S) - C1-53 (E1) LG - BR M shift position switch signal Ignition switch ON, shift lever in M 11 to 14 V
Ignition switch ON, shift lever not in M Below 1 V
A43-18 (FPC) - C1-53 (E1) P - BR Fuel pump control Engine stopped, ignition switch ON Below 1.5 V
A43-26 (CANL) - C1-53 (E1) W - BR CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 2)
A43-27 (STP) - C1-53 (E1) G - BR Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A43-30 (NEO)*1 - C1-53 (E1) GR - BR Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 3)
A43-33 (TC) - C1-53 (E1) G - BR Terminal TC of DLC3 Engine stopped, ignition switch ON 11 to 14 V
A43-39 (SPD) - C1-53 (E1) BE - BR Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 4)
A43-42 (ST1-) - C1-53 (E1) L - BR Stop light switch assembly signal (opposite to STP terminal) Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A43-43 (STA) - C1-53 (E1) P - BR Starter assembly signal Cranking 6.0 V or higher
A43-46 (MREL) - C1-53 (E1) B - BR EFI-MAIN relay operation signal Ignition switch ON 11 to 14 V
A43-47 (VPA) - A43-48 (EPA) G - Y Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A43-49 (VCPA) - A43-48 (EPA) B - Y Power source of accelerator pedal position sensor (for VPA) Engine stopped, ignition switch ON 4.5 to 5.5 V
A43-50 (VPA2) - A43-51 (EPA2) R - BE Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed 3.4 to 4.75 V
A43-52 (VCP2) - A43-51 (EPA2) W - BE Power source of accelerator pedal position sensor (for VPA2) Engine stopped, ignition switch ON 4.5 to 5.5 V
A43-58 (KSW) - C1-53 (E1) B - BR Key in vehicle signal Ignition switch off → on (IG) 0 to 3.0 V
C1-2 (OE2+) - C1-3 (OE2-) R -W Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2) operation signal Idling Pulse generation
(See waveform 5)
C1-4 (OE1+) - C1-5 (OE1-) G - R Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1) operation signal Idling Pulse generation
(See waveform 5)
C1-9 (OC2+) - C1-8 (OC2-) B - L Cam timing oil control solenoid assembly (for intake camshaft of bank 2) operation signal Idling Pulse generation
(See waveform 6)
C1-16 (HT2B) - C1-53 (E1) L - BR Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C1-17 (HA2A) - C1-46 (E05) R - W-B Air fuel ratio sensor (bank 2 sensor 1) heater operation signal Idling Pulse generation
(See waveform 7)
Ignition switch ON 11 to 14 V
C1-18 (+BD2) - C1-53 (E1) L - BR Power source of ECM (injector driver) Engine stopped, ignition switch ON 11 to 14 V
C1-19 (+BD1) - C1-53 (E1) Y - BR Power source of ECM (injector driver) Engine stopped, ignition switch ON 11 to 14 V
C1-20 (E02) - Body ground W-B - - Ground Always Below 1 Ω
C1-21 (E04) - Body ground W-B - - Ground Always Below 1 Ω
C1-23 (FP1+) - C1-22 (FP1-) Y - L Fuel pump assembly (for high pressure side) signal Idling with warm engine Pulse generation
C1-24 (#6D+) - C1-54 (#6D-) G - BR No. 6 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C1-25 (#3D+) - C1-26 (#3D-) V - P No. 3 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C1-27 (#5D+) - C1-57 (#5D-) L - Y No. 5 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C1-28 (#2D+) - C1-58 (#2D-) G - BR No. 2 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C1-29 (#4D+) - C1-59 (#4D-) V - P No. 4 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C1-30 (#1D+) - C1-60 (#1D-) B - W No. 1 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C1-34 (IGT6) - C1-53 (E1) V - BR No. 6 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C1-35 (IGT4) - C1-53 (E1) B - BR No. 4 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C1-36 (IGT2) - C1-53 (E1) GR - BR No. 2 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C1-38 (OC1+) - C1-68 (OC1-) W - G Cam timing oil control solenoid assembly (for intake camshaft of bank 1) operation signal Idling Pulse generation
(See waveform 6)
C1-40 (#60) - C1-51 (E01) G - W-B No. 6 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C1-41 (#30) - C1-51 (E01) B - W-B No. 3 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C1-42 (#50) - C1-51 (E01) R - W-B No. 5 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C1-43 (#20) - C1-51 (E01) BE - W-B No. 2 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C1-44 (#40) - C1-51 (E01) W - W-B No. 4 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C1-45 (#10) - C1-51 (E01) GR - W-B No. 1 fuel injector assembly (for port injection) signal Ignition switch ON 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C1-46 (E05) - Body ground W-B - - Ground Always Below 1 Ω
C1-47 (M-) - C1-49 (ME01) P - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 10)
C1-48 (M+) - C1-49 (ME01) V - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 11)
C1-49 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
C1-50 (HT1B) - C1-53 (E1) L - BR Heated oxygen sensor (bank 1 sensor 2) heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C1-51 (E01) - Body ground W-B - - Ground Always Below 1 Ω
C1-52 (HA1A) - C1-21 (E04) B - W-B Air fuel ratio sensor (bank 1 sensor 1) heater operation signal Idling Pulse generation
(See waveform 7)
Ignition switch ON 11 to 14 V
C1-53 (E1) - Body ground BR - - Ground Always Below 1 Ω
C1-55 (E1D2) - Body ground B - - Ground Always Below 1 Ω
C1-56 (E1D1) - Body ground W - - Ground Always Below 1 Ω
C1-64 (PTCR) - C1-53 (E1) L - BR Thermostat heater operation signal Ignition switch ON 11 to 14 V
C1-65 (PRG) - C1-53 (E1) R - BR Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 12)
C1-66 (ACIS) - C1-53 (E1) L - BR No. 1 vacuum switching valve (for intake air control valve sub-assembly) operation signal Ignition switch ON 11 to 14 V
C1-69 (IGT5) - C1-53 (E1) R - BR No. 5 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C1-70 (IGT3) - C1-53 (E1) L - BR No. 3 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C1-71 (IGT1) - C1-53 (E1) GR - BR No. 1 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C1-80 (IGF2) - C1-53 (E1) LG - BR Ignition coil assembly (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling with warm engine Pulse generation
(See waveform 8)
C1-82 (KNK1) - C1-81 (EKNK) B - W Knock control sensor (bank 1) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 13)
C1-87 (PR) - C1-133 (ETHW) P - BR Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
C1-89 (VTA2) - C1-120 (ETA) LG - B Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
C1-90 (VC) - C1-53 (E1) W - BR Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-91 (OX2B) - C1-92 (EX2B) G - W Heated oxygen sensor (bank 2 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 14)
C1-93 (OX1B) - C1-94 (EX1B) R - G Heated oxygen sensor (bank 1 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 14)
C1-96 (VCNE) - C1-53 (E1) R - BR Power source of crankshaft position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-98 (VCV2) - C1-97 (VV2-) R - B Power source of VVT sensor (bank 2) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-99 (VCV1) - C1-100 (VV1-) W - R Power source of VVT sensor (bank 1) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-101 (THW) - C1-133 (ETHW) B - BR Engine coolant temperature sensor Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C1-102 (THA) - C1-115 (E2G) L - LG Intake air temperature sensor Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C1-105 (SNWI) - C1-53 (E1) BE - BR SNOW mode switch signal Ignition switch ON 11 to 14 V
Ignition switch ON, SNOW mode switch being pushed and held Below 1.5 V
C1-106 (NSW) - C1-53 (E1) G - BR Park/Neutral position switch assembly signal Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 1 V
C1-107 (R) - C1-53 (E1) B - BR R shift position switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
C1-108 (P) - C1-53 (E1) G - BR P shift position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
C1-112 (IGF1) - C1-53 (E1) B - BR Ignition coil assembly (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling with warm engine Pulse generation
(See waveform 8)
C1-114 (KNK2) - C1-113 (EKN2) R - G Knock control sensor (bank 2) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 13)
C1-116 (VG) - C1-115 (E2G) R - LG Mass air flow meter sub-assembly signal Ignition switch ON Pulse generation
(See waveform 15)
C1-121 (VCTA) - C1-120 (ETA) R - B Power source of throttle position sensor (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C1-122 (VTA1) - C1-120 (ETA) G - B Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
C1-123 (A2A+) - C1-53 (E1) P - BR Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 3.3 V*2
C1-124 (A2A-) - C1-53 (E1) L - BR Air fuel ratio sensor (bank 2 sensor 1) signal Ignition switch ON 2.9 V*2
C1-125 (A1A+) - C1-53 (E1) Y - BR Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 3.3 V*2
C1-126 (A1A-) - C1-53 (E1) BR - BR Air fuel ratio sensor (bank 1 sensor 1) signal Ignition switch ON 2.9 V*2
C1-127 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
C1-128 (NE+) - C1-95 (NE-) L - B Crankshaft position sensor Idling with warm engine Pulse generation
(See waveform 16)
C1-129 (VV2+) - C1-97 (VV2-) G - B VVT sensor (for intake camshaft of bank 2) signal Idling Pulse generation
(See waveform 17)
C1-130 (EV2+) - C1-97 (VV2-) GR - B VVT sensor (for exhaust camshaft of bank 2) signal Idling Pulse generation
(See waveform 18)
C1-131 (EV1+) - C1-100 (VV1-) B - R VVT sensor (for exhaust camshaft of bank 1) signal Idling Pulse generation
(See waveform 18)
C1-132 (VV1+) - C1-100 (VV1-) G - R VVT sensor (for intake camshaft of bank 1) signal Idling Pulse generation
(See waveform 17)
C1-134 (PFL) - C1-133 (ETHW) R - BR Fuel pressure sensor (for low pressure side) signal Idling with warm engine 0.75 to 4.5 V
C1-136 (RFC) - C1-53 (E1) LG - BR Cooling fan control signal Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 19)
C1-139 (D) - C1-53 (E1) R - BR D shift position switch signal Ignition switch ON, shift lever in D or M 11 to 14 V
Ignition switch ON, shift lever not in D or M Below 1 V
C1-140 (N) - C1-53 (E1) W - BR N shift position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V

*1: w/ Smart Entry and Start System.

*2: The ECM terminal voltage is constant regardless of the voltage output from the sensor.

WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A287796E02
2.594,1.656 3.052,1.854 0.458,0.198 10 GND 0.063,0.063 0.781,0.292 0.719,0.229 10 1 V/DIV. 1.167,1.927 2,2.135 0.833,0.208 10 2 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A283573E11
2.677,0.125 3.354,0.385 0.677,0.26 10 false 2 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 false GND 1.156,1.99 2.219,2.167 1.063,0.177 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 5


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly (for Exhaust Camshaft) Signal
ECM Terminal Name Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 6


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) Signal
ECM Terminal Name Between OC1+ and OC1-
Between OC2+ and OC2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 7


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Between HA2A and E05
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling


WAVEFORM 8


A369419E01
0.031,0.052 0.583,0.271 0.552,0.219 10 false 2 V/DIV. 0.135,0.781 0.469,1 0.333,0.219 10 false CH1 0.146,1.25 0.469,1.458 0.323,0.208 10 false CH2 1.25,1.948 2.073,2.167 0.823,0.219 10 false 20 ms./DIV. 2.99,0.99 3.365,1.219 0.375,0.229 10 false GND 2.99,1.635 3.354,1.844 0.365,0.208 10 false GND

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name CH1: Between IGT (1 to 6) and E1
CH2: Between IGF (1 or 2) and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 9


A287799E11
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

No. 1 (to No. 6) Fuel Injector Assembly (for Port Injection) Signal
ECM Terminal Name Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Port"

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Way of the Data List.




WAVEFORM 10


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 11


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 13


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed will differ slightly depending on the vehicle.




WAVEFORM 14


A283571E01
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Between OX2B and EX2B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

Data List, item "O2 Sensor Voltage B1S2" and "O2 Sensor Voltage B2S2" shows the ECM values from the heated oxygen sensor.



WAVEFORM 15


A337204E05
0.115,1.417 0.469,1.615 0.354,0.198 10 false GND 1.406,1.958 2.188,2.156 0.781,0.198 10 false 100 μs./DIV. 2.813,0.167 3.406,0.375 0.594,0.208 10 false 1 V/DIV.

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Ignition switch ON


WAVEFORM 16


A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A356009E02
0.094,1.323 0.479,1.542 0.385,0.219 10 false CH1 0.135,2.063 0.469,2.271 0.333,0.208 10 false CH2 2.813,1.479 3.271,1.677 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND 2.677,0.771 3.302,1 0.625,0.229 10 false 5 V/DIV. 1.25,2.552 2.938,2.75 1.688,0.198 10 false 20 ms./DIV.

VVT Sensor (for Intake Camshaft) Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 18


A356008E02
0.094,1.365 0.438,1.573 0.344,0.208 10 false CH1 0.115,2.094 0.458,2.302 0.344,0.208 10 false CH2 1.26,2.542 2.167,2.802 0.906,0.26 10 false 20 ms./DIV. 2.802,1.469 3.26,1.667 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND 2.698,0.771 3.302,1.021 0.604,0.25 10 false 5 V/DIV.

VVT Sensor (for Exhaust Camshaft) Signal
ECM Terminal Name CH1: Between EV1+ and VV1-
CH2: Between EV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A282867E08
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.