84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check for defects with the spiral cable sub-assembly.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any defects are found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *A | w/o Steering Heater | *B | w/ Steering Heater |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
*b | Color: Orange |
| *c | Color: Black | - | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/ Steering Heater |
||
| F61-1 (CCS) - z8-3 (CCS) | Always | 3 Ω or less |
| F61-2 (ECC) - z4-7 (ECC) | Always | 3 Ω or less |
| F61-2 (ECC) - z8-4 (ECC) | Always | 3 Ω or less |
| F61-3 (EAU) - z4-8 (EAU) | Always | 3 Ω or less |
| F61-4 (IL-2) - z4-9 (IL-2) | Always | 3 Ω or less |
| F61-5 (AU2) - z4-10 (AU2) | Always | 3 Ω or less |
| F61-6 (AU1) - z4-11 (AU1) | Always | 3 Ω or less |
| F61-8 (ILL-) - z8-1 (ILL-) | Always | 3 Ω or less |
| F61-9 (IL+2) - z4-1 (IL+2) | Always | 3 Ω or less |
| F61-9 (IL+2) - z8-2 (IL+2) | Always | 3 Ω or less |
| F61-10 (+DP) - z4-2 (+DP) | Always | 3 Ω or less |
| F61-11 (+DP2) - z4-3 (+DP2) | Always | 3 Ω or less |
| F61-12 (DIST) - z4-4 (DIST) | Always | 3 Ω or less |
| F61-13 (HO) - z4-5 (HO) | Always | 3 Ω or less |
| F63-1 (D+) - z6-2 (D+) | Always | Below 1 Ω |
| F63-2 (D-) - z6-1 (D-) | Always | Below 1 Ω |
| F63-3 (D2-) - z5-1 (D2-) | Always | Below 1 Ω |
| F63-4 (D2+) - z5-2 (D2+) | Always | Below 1 Ω |
| F62-1 (BTM) - z7-1 (BTM)* | Always | 3 Ω or less |
| F62-2 (EHT) - z7-3 (EHT)* | Always | Below 0.1 Ω |
| F62-3 (ETM) - z7-2 (ETM)* | Always | 3 Ω or less |
| F62-4 (BHT) - z7-4 (BHT)* | Always | Below 0.1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/ Steering Heater |
||
| F61-1 (CCS) - z8-3 (CCS) | Always | 3 Ω or less |
| F61-2 (ECC) - z4-7 (ECC) | Always | 3 Ω or less |
| F61-2 (ECC) - z8-4 (ECC) | Always | 3 Ω or less |
| F61-3 (EAU) - z4-8 (EAU) | Always | 3 Ω or less |
| F61-4 (IL-2) - z4-9 (IL-2) | Always | 3 Ω or less |
| F61-5 (AU2) - z4-10 (AU2) | Always | 3 Ω or less |
| F61-6 (AU1) - z4-11 (AU1) | Always | 3 Ω or less |
| F61-8 (ILL-) - z8-1 (ILL-) | Always | 3 Ω or less |
| F61-9 (IL+2) - z4-1 (IL+2) | Always | 3 Ω or less |
| F61-9 (IL+2) - z8-2 (IL+2) | Always | 3 Ω or less |
| F61-10 (+DP) - z4-2 (+DP) | Always | 3 Ω or less |
| F61-11 (+DP2) - z4-3 (+DP2) | Always | 3 Ω or less |
| F61-12 (DIST) - z4-4 (DIST) | Always | 3 Ω or less |
| F61-13 (HO) - z4-5 (HO) | Always | 3 Ω or less |
| F63-1 (D+) - z6-2 (D+) | Always | Below 1 Ω |
| F63-2 (D-) - z6-1 (D-) | Always | Below 1 Ω |
| F63-3 (D2-) - z5-1 (D2-) | Always | Below 1 Ω |
| F63-4 (D2+) - z5-2 (D2+) | Always | Below 1 Ω |
| F62-1 (BTM) - z7-1 (BTM)* | Always | 3 Ω or less |
| F62-2 (EHT) - z7-3 (EHT)* | Always | Below 0.1 Ω |
| F62-3 (ETM) - z7-2 (ETM)* | Always | 3 Ω or less |
| F62-4 (BHT) - z7-4 (BHT)* | Always | Below 0.1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*: w/ Steering Heater |
||
| F61-1 (CCS) - z8-3 (CCS) | Always | 3 Ω or less |
| F61-2 (ECC) - z4-7 (ECC) | Always | 3 Ω or less |
| F61-2 (ECC) - z8-4 (ECC) | Always | 3 Ω or less |
| F61-3 (EAU) - z4-8 (EAU) | Always | 3 Ω or less |
| F61-4 (IL-2) - z4-9 (IL-2) | Always | 3 Ω or less |
| F61-5 (AU2) - z4-10 (AU2) | Always | 3 Ω or less |
| F61-6 (AU1) - z4-11 (AU1) | Always | 3 Ω or less |
| F61-8 (ILL-) - z8-1 (ILL-) | Always | 3 Ω or less |
| F61-9 (IL+2) - z4-1 (IL+2) | Always | 3 Ω or less |
| F61-9 (IL+2) - z8-2 (IL+2) | Always | 3 Ω or less |
| F61-10 (+DP) - z4-2 (+DP) | Always | 3 Ω or less |
| F61-11 (+DP2) - z4-3 (+DP2) | Always | 3 Ω or less |
| F61-12 (DIST) - z4-4 (DIST) | Always | 3 Ω or less |
| F61-13 (HO) - z4-5 (HO) | Always | 3 Ω or less |
| F63-1 (D+) - z6-2 (D+) | Always | Below 1 Ω |
| F63-2 (D-) - z6-1 (D-) | Always | Below 1 Ω |
| F63-3 (D2-) - z5-1 (D2-) | Always | Below 1 Ω |
| F63-4 (D2+) - z5-2 (D2+) | Always | Below 1 Ω |
| F62-1 (BTM) - z7-1 (BTM)* | Always | 3 Ω or less |
| F62-2 (EHT) - z7-3 (EHT)* | Always | Below 0.1 Ω |
| F62-3 (ETM) - z7-2 (ETM)* | Always | 3 Ω or less |
| F62-4 (BHT) - z7-4 (BHT)* | Always | Below 0.1 Ω |
If the result is not as specified, replace the spiral cable sub-assembly.