Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a ground short in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted via the CAN communication system to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C265835E40
1.375,0.917 1.719,1.271 0.344,0.354 10 false 26 1.365,0.219 1.656,0.594 0.292,0.375 10 false 13 1.375,2.094 2.198,2.49 0.823,0.396 10 false 23*1, 33*2 0.917,1.063 1.396,1.313 0.479,0.25 10 false CANL 0.906,0.354 1.656,0.698 0.75,0.344 10 false CANH 1.104,2.188 1.531,2.604 0.427,0.417 10 false TC 0.771,3.344 1.635,3.604 0.865,0.26 10 false A43 0.781,3.49 1.26,3.813 0.479,0.323 10 false ECM 0.438,3.896 1.542,4.188 1.104,0.292 10 false *1: for 1AR-FE 0.438,4.167 1.5,4.438 1.063,0.271 10 false *2: for 2GR-FKS 5.927,2.188 6.26,2.542 0.333,0.354 10 false TC 5.688,2.094 6.042,2.427 0.354,0.333 10 false 13 5.76,2.708 5.979,3.042 0.219,0.333 10 false 4 5.927,2.802 6.25,3.104 0.323,0.302 10 false CG 6.146,3.344 6.573,3.573 0.427,0.229 10 false F25 6.146,3.49 6.646,3.833 0.5,0.344 10 false DLC3 5.938,1.052 6.448,1.417 0.51,0.365 10 false CANL 5.573,1.49 5.917,1.74 0.344,0.25 10 false F38 5.677,0.917 6,1.281 0.323,0.365 10 false 22 5.677,0.208 5.948,0.521 0.271,0.313 10 false 13 5.938,0.354 6.406,0.698 0.469,0.344 10 false CANH 5.563,1.635 7.125,2.01 1.563,0.375 10 false Airbag Sensor Assembly 0.854,4.531 2.615,4.75 1.76,0.219 10 false : CAN Communication Line

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF ECM)
a.
C238361C31
0.552,0.125 0.938,0.365 0.385,0.24 0.583,2.208 0.938,2.438 0.354,0.229 1.802,1.208 1.802,1.542 false 1.271,3.542 0.865,4.25 false 2.396,3.344 2.75,4.26 false 0.167,0.125 0.479,0.51 0.313,0.385 10 false *1 0.167,2.01 0.438,2.396 0.271,0.385 10 false *a 1.729,1.563 2.063,1.938 0.333,0.375 10 false TC 0.635,2.24 0.938,2.594 0.302,0.354 10 false A43 0.635,0.156 0.906,0.469 0.271,0.313 10 false F25 0.76,4.271 1.177,4.521 0.417,0.25 10 false TC*B 2.667,4.271 3.125,4.583 0.458,0.313 10 false TC*A
*A for 1AR-FE
*B for 2GR-FKS
*1 DLC3
*a Front view of wire harness connector
(to ECM)


Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1AR-FE:
Tester Connection Condition Specified Condition
F25-13 (TC) - A43-23 (TC) Always Below 1 Ω

for 2GR-FKS:
Tester Connection Condition Specified Condition
F25-13 (TC) - A43-33 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C23
0.135,0.979 0.469,1.198 0.333,0.219 1.615,0.802 1.615,0.302 1.615,0.302 1.813,0.302 false 0.156,0.135 0.469,0.396 0.313,0.26 10 false *1 0.188,1.01 0.5,1.313 0.313,0.302 10 false F25 1.854,0.219 2.25,0.469 0.396,0.25 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C24
0.188,0.958 0.521,1.188 0.333,0.229 1.958,1.76 1.792,1.76 1.792,1.76 1.792,1.344 false 0.125,0.115 0.406,0.396 0.281,0.281 10 false *1 0.24,0.99 0.802,1.448 0.563,0.458 10 false F25 2.021,1.688 2.354,1.979 0.333,0.292 10 false TC
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU