Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C306841C06
0.156,0.146 0.469,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


Terminal No. (Symbol) Terminal Description
1 (GND2) Pump motor ground
2 - (Not used)
3 - (Not used)
4 - (Not used)
5 (STP2) Stop light control relay (stop light switch assembly) input
6 - (Not used)
7 - (Not used)
8 - (Not used)
9 - (Not used)
10 (CANL) CAN communication line L
11 - (Not used)
12 (IG1) IG1 power source input
13 (BM) ABS motor relay power supply
14 (SP1) Speed signal output for speedometer
15 (RR-) Rear wheel speed RH (-) signal input
16 (RR+) Rear wheel speed RH (+) power supply output
17 (FL-) Front wheel speed LH (-) signal input
18 (FL+) Front wheel speed LH (+) power supply output
19 - (Not used)
20 - (Not used)
21 - (Not used)
22 (CANH) CAN communication line H
23 (FSW+) Brake pedal load sensing switch (brake pedal support assembly) input
24 - (Not used)
25 (GND1) Skid control ECU (brake actuator assembly) ground
26 (STPO) Stop light control relay (stop light switch assembly) output
27 (HDCS)* Downhill assist control switch input
28 (RL-) Rear wheel speed LH (-) signal input
29 (RL+) Rear wheel speed LH (+) power supply output
30 (FR-) Front wheel speed RH (-) signal input
31 (FR+) Front wheel speed RH (+) power supply output
32 - (Not used)
33 (CSW) VSC OFF switch input
34 - (Not used)
35 (STP) Stop light switch assembly input
36 - (Not used)
37 - (Not used)
38 (+BS) ABS solenoid relay power supply

*: for AWD


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

C306842C31
3.365,0.281 3.823,0.604 0.458,0.323 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 3.469,0.354 3.927,0.552 0.458,0.198 10 false A86
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -


HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A86-1 (GND2) - Body ground W-B - Body ground Skid control ECU (brake actuator assembly) ground Always Below 1 Ω
A86-5 (STP2) - Body ground G - Body ground Stop light control relay (stop light switch assembly) input Stop light switch assembly on → off (Brake pedal depressed → released) 8 to 14 V → Below 1.5 V
A86-12 (IG1) - Body ground LG - Body ground IG1 power source input Ignition switch ON 11 to 14 V
A86-13 (BM) - Body ground R - Body ground ABS motor relay power supply Always 11 to 14 V
A86-14 (SP1) - Body ground LG - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A86-23 (FSW+) - Body ground R - Body ground Brake pedal load sensing switch (brake pedal support assembly) input Brake pedal load sensing switch (brake pedal support assembly) off → on (Brake pedal depressed → released) 950 to 1050 Ω → 203 to 223 Ω
A86-25 (GND1) - Body ground W - Body ground Pump motor ground Always Below 1 Ω
A86-26 (STPO) - Body ground GR - Body ground Stop light control relay (stop light switch assembly) output Ignition switch ON 11 to 14 V
A86-27 (HDCS) - Body ground* G - Body ground Downhill assist control switch input Downhill assist control switch is pushed → released Below 1 Ω → 10 kΩ or higher
A86-33 (CSW) - Body ground BE - Body ground VSC OFF switch input VSC OFF switch on → off (Pressed → not pressed) Below 1 Ω → 10 kΩ or higher
A86-35 (STP) - Body ground L - Body ground Stop light switch assembly input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A86-38 (+BS) - Body ground L - Body ground ABS solenoid relay power supply Always 11 to 14 V

*: for AWD