Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY(When Using the Engine Support Bridge) › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0299917 VALVE BODY ASSEMBLY(When Using the Engine Support Bridge) G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY(When Using the Engine Support Bridge)  INSPECTION  


PROCEDURE

Hide 35240 1.INSPECT SHIFT SOLENOID VALVE SL

a.
C188295C01
0.158,0.099 0.355,0.264 0.197,0.164 10 *a
*a Component without harness connected
(Shift Solenoid Valve SL)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid Connector (SL) - Solenoid Body (SL) 20°C (68°F) 11 to 15 Ω


If the value is not as specified, replace the shift solenoid valve SL.


b.

Connect a positive (+) lead from the battery to the terminal of the solenoid connector and a negative (-) lead to the solenoid body, and check the operation of the valve.

NOTICE:

When using battery voltage during this inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.


OK:

The valve moves and makes an operating sound.


If the operation is not as specified, replace the shift solenoid valve SL.


Hide 35290 2.INSPECT SHIFT SOLENOID VALVE SLT

a.
C201747C11
1.448,0.865 0.594,0.635 true 1.802,0.865 2.5,0.625 true 1.438,3.135 0.583,2.906 true 1.823,3.115 2.521,2.875 true 0.5,0.542 0.677,0.74 0.177,0.198 10 false 1 2.542,0.531 2.719,0.729 0.177,0.198 10 false 2 1.167,4.188 1.375,4.396 0.208,0.208 10 false (-) 1.917,4.188 2.146,4.385 0.229,0.198 10 false (+) 0.49,2.802 0.667,3 0.177,0.198 10 false 1 2.563,2.771 2.74,2.969 0.177,0.198 10 false 2 0.052,0.063 0.271,0.271 0.219,0.208 10 false *a 2.823,3.563 3.135,3.76 0.313,0.198 10 false *b
*a Component without harness connected
(Shift Solenoid Valve SLT)
*b 21 W Bulb


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω


If the value is not as specified, replace the shift solenoid valve SLT.


b.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

NOTICE:

When using battery voltage during this inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.


OK:

The valve moves and makes an operating sound.


If the operation is not as specified, replace the shift solenoid valve SLT.


Hide 35280 3.INSPECT SHIFT SOLENOID VALVE SLU

HINT:

Use the same procedure as for the shift solenoid valve SLT.


Hide 35210 4.INSPECT SHIFT SOLENOID VALVE SL1

HINT:

Use the same procedure as for the shift solenoid valve SLT.


Hide 35220 5.INSPECT SHIFT SOLENOID VALVE SL2

HINT:

Use the same procedure as for the shift solenoid valve SLT.


Hide 6.INSPECT SHIFT SOLENOID VALVE SL3

HINT:

Use the same procedure as for the shift solenoid valve SLT.


Hide 7.INSPECT SHIFT SOLENOID VALVE SL4

HINT:

Use the same procedure as for the shift solenoid valve SLT.