The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.
The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch assembly off.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1422/22 | Compressor Lock Sensor Circuit | Open or short in A/C lock sensor circuit (for 2GR-FKS) | ·
Magnetic clutch assembly ·
Cooler compressor assembly ·
Harness or connector between cooler compressor assembly and air conditioning amplifier assembly ·
Air conditioning amplifier assembly |
Memorized
(3 sec. or more)* |
*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
ECM malfunctions can affect the storage of this DTC. Therefore, check all SFI system DTCs and confirm that the system is normal before performing the following inspection.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the magnetic clutch assembly connector.
Install SST to the connector on the magnetic clutch relay side.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Magnetic Clutch Relay | Air conditioning system operation | OFF or ON | - |
| *a | Front view of wire harness connector
(to Magnetic Clutch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | ·
Engine is running ·
Active Test above is being performed |
11 to 14 V |
When performing the Active Test, voltage between 11 and 14 V is output for approximately 3 seconds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Magnetic Clutch Assembly) |
Connect the magnetic clutch assembly connector.
Disconnect the C12 cooler compressor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (MG+) - Body ground | 20°C (68°F) | 3.8 to 4.2 Ω |
Connect a positive (+) lead from the battery to terminal 3 (MG+) and check that the following occurs: 1) the magnetic clutch assembly operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Cooler Compressor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SSR+) - 2 (SSR-) | 20°C (68°F) | 160 to 320 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F80 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C12-1 (SSR+) - F80-8 (LOCK) | Always | Below 1 Ω |
| C12-2 (SSR-) - F80-13 (SG-2) | Always | Below 1 Ω |
| C12-1 (SSR+) or F80-8 (LOCK) - Body ground | Always | 10 kΩ or higher |
| C12-2 (SSR-) or F80-13 (SG-2) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (When troubleshooting according to Problem Symptoms Table) | A |
| OK (When troubleshooting according to the DTC) | B |
| NG | C |
A
B
C