Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › from 2016.11
RM3160E _53 Suspension _019688 ALIGNMENT / HANDLING DIAGNOSIS _0109428 REAR WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

If a wheel alignment has been performed, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



PROCEDURE

Hide 3.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-0.51° +/- 0.75°(-0°31' +/- 0°45') 0.75°(0°45') or less


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



Hide 4.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



f.
C301346C01
0.635,1.635 0.635,1.167 false 0.563,1.688 0.875,1.844 0.313,0.156 10 false *a 2.469,0.573 2.625,0.771 0.156,0.198 10 false A 2.5,1.667 2.656,1.865 0.156,0.198 10 false B 1.844,0.396 2,0.594 0.156,0.198 10 false C 3.156,0.385 3.313,0.583 0.156,0.198 10 false D
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: -0.08° +/- 0.17° (-0°05' +/- 0°10')
B - A: -1.0 +/- 2.0 mm (-0.0394 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it by following the procedures below.


Hide 5.ADJUST TOE-IN

a.
C199848C01
0.167,0.042 3.354,2.313 3.188,2.271 0.167,2.344 3.354,4.635 3.188,2.292 0.24,0.094 0.552,0.333 0.313,0.24 10 true *A 0.229,2.385 0.542,2.625 0.313,0.24 10 true *B
*A LH Side
*B RH Side


Loosen the nut of the rear No. 2 suspension arm assembly (on the rear suspension member sub-assembly side).

NOTICE:

Hold the toe adjust cam sub-assembly while rotating the nut.



b.

Rotate the toe adjust cam sub-assembly to adjust the toe-in.

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: -0.08° +/- 0.17° (-0°05' +/- 0°10')
B - A: -1.0 +/- 2.0 mm (-0.0394 +/- 0.0787 in.)


HINT:

Rotating the rear suspension toe adjust cam sub-assembly by one notch changes the toe by approximately 2.1 mm (0.0827 in.).



c.

Tighten the nut of the rear No. 2 suspension arm assembly (on the rear suspension member sub-assembly side).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:
·

Hold the toe adjust cam sub-assembly while rotating the nut.

·

Tighten the nut of the rear No. 2 suspension arm assembly while the vehicle is unloaded.




Hide 6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 7. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION