Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0097257 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


TELEVISION CAMERA ASSEMBLY


a.

Disconnect the X12 television camera assembly connector.

E267064N10
3.385,0.083 3.771,0.333 0.385,0.25 3.469,0.146 3.781,0.344 0.313,0.198 10 false X12


b.

Measure the voltage of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X12-6 (CB+) - Body ground B - Body ground Power source Ignition switch ACC 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the X12 television camera assembly connector.


d.

Measure the resistance and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X12-3 (CV+) - X12-2 (CV-) R - W Video signal Ignition switch ON
Shift lever in R
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Ignition switch ON
Shift lever in R
Camera lens covered, blacking out the screen
Pulse generation
(Refer to waveform 2)
X12-5 (CGND) - Body ground BR - Body ground Shield ground Always Below 1 Ω

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly*1 navigation receiver assembly*2 with the connector connected.

*1: w/o Navigation System

*2: w/ Navigation System



If the result is not as specified, the television camera assembly may be malfunctioning.


e.
E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly*1 navigation receiver assembly*2 with the connector connected.

*1: w/o Navigation System

*2: w/ Navigation System



i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal X12-3 (CV+) - X12-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal X12-3 (CV+) - X12-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.






RADIO AND DISPLAY RECEIVER ASSEMBLY (w/o Navigation System)


Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU