Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1421  Open or Short in Master Cylinder Pressure Sensor  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  C142A  Master Cylinder Pressure Sensor Internal Malfunction  C1449  Master Cylinder Output Value Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1421 Open or Short in Master Cylinder Pressure Sensor Any of the following is detected:
1.

When voltage at terminal +BS is 9.5 V or higher, power supply voltage of master cylinder pressure sensor is continuously low for 1 second or more.

2.

When master cylinder pressure sensor power supply voltage has risen, master cylinder pressure sensor has overheated or overcurrent of master cylinder pressure sensor continues for 0.1 seconds or more.

3.

When +BS terminal voltage is 9.5 to 17.4 V, there is no communication with master cylinder pressure sensor continuously for 0.1 seconds or more.


Master cylinder pressure sensor (brake actuator assembly)
C1423 Master Cylinder Pressure Sensor Zero Point Low Malfunction Master cylinder pressure is below -0.744 Mpa (-7.6 kgf/cm2, -107 psi) for 5 seconds or more. Master cylinder pressure sensor (brake actuator assembly)
C1424 Master Cylinder Pressure Sensor Output Malfunction Any of the following is detected:
1.

When vehicle speed is 7 km/h (4.3 mph) or more and master cylinder pressure exceeds 1.764 Mpa (18.0 kgf/cm2, 255 psi), master cylinder pressure does not increase 0.048 Mpa (0.5 kgf/cm2, 6.9 psi) or more continuously for 60 seconds.

2.

When vehicle speed is 7 km/h (4.3 mph) and master cylinder pressure is 2.45 Mpa (25.0 kgf/cm2, 355 psi) or more, master cylinder pressure does not increase 0.048 Mpa (0.5 kgf/cm2, 6.9 psi) or more continuously for 30 seconds.

3.

Master cylinder pressure does not increase 0.048 Mpa (0.5 kgf/cm2, 6.9 psi) or more 5 times or more while vehicle speed decreases from 40 km/h (25 mph) to 0 km/h (0 mph).

4.

When vehicle speed is 10 km/h (6 mph) or more, noise in master cylinder pressure value occurs 7 times or more in 5 seconds.

5.

When vehicle speed is 7 km/h (4.3 mph) or more, braking is performed (stop light switch assembly is ON) and master cylinder pressure differential value is below 20 Mpa/s, difference between master cylinder pressure estimated from vehicle deceleration and master cylinder pressure sensor input value is large for 1 second or more 5 times or more.


Master cylinder pressure sensor (brake actuator assembly)
C142A Master Cylinder Pressure Sensor Internal Malfunction Either of the following is detected:
1.

Master cylinder pressure is 23.328 Mpa (237.8 kgf/cm2, 3382 psi) or more continuously for 0.1 seconds.

2.

Master cylinder temperature is 150°C (302°F) or more continuously for 0.1 seconds.


Master cylinder pressure sensor (brake actuator assembly)
C1449 Master Cylinder Output Value Malfunction Master cylinder pressure sensor invalid condition continues for 0.2 seconds or more. Master cylinder pressure sensor (brake actuator assembly)

HINT:

for C1423 and C1424: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:

1.

Turn the ignition switch to ON.

2.

Keep the vehicle stationary for 5 seconds or more and depress the brake pedal lightly 2 or 3 times.

3.

Drive the vehicle at the vehicle speed of 50 km/h (31 mph) and depress and hold the brake pedal firmly for approximately 3 seconds.

4.

Repeat the above operation 3 times or more and check that the ABS warning light goes off.

5.

Clear the DTCs.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the master cylinder pressure sensor (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


b.

Perform zero point calibration of the yaw rate and acceleration sensor and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
Test Mode
50005 105 166

c.

Perform the sensor check in Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

Result:
Proceed to
NEXT



NEXT

END