DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ABS Warning Light | ABS warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Brake Warning Light | Brake warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Downhill Assist Control Light | Downhill assist control indicator light | ON or OFF | ON: Indicator light on
OFF: Indicator light off |
for AWD |
| Buzzer | Meter buzzer | ON or OFF | ON: Buzzer on
OFF: Buzzer off |
- |
| Stop Light SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Parking Brake SW | Parking brake switch assembly | ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch | ON or OFF | ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point |
- |
| Gear Position | Gear position information | P, N, R, 1st-8th, Fail or Not R | Actual gear position | - |
| Shift Lever Position | Shift lever position information | P, N, R, D/M, 1st-6th/B or Fail | Actual shift lever position | - |
| Inspection Mode | Inspection mode | Other or Inspect | Other: Normal mode
Inspect: Inspection mode |
- |
| Downhill Assist Control SW | Downhill assist control switch | ON or OFF | ON: Switch on
OFF: Switch off |
for AWD |
| Zero Point of M/C | Memorized zero value | Min.: -12.50 Mpa, Max.: 12.40 Mpa | - | After master cylinder pressure sensor zero point calibration: 2.44 to 2.46 Mpa |
| Deceleration Sensor | Acceleration sensor reading | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Zero Point of Decele | Memorized zero value | Min.: -25.10 m/s2, Max.: 24.90 m/s2 | - | - |
| Deceleration Sensor2 | Acceleration sensor 2 reading | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Zero Point of Decele2 | Memorized zero value | Min.: -25.10 m/s2, Max.: 24.90 m/s2 | - | - |
| Yaw Rate Sensor | Yaw rate sensor | Min.: -128°/s, Max.: 127°/s | Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Zero Point of Yaw Rate | Memorized zero value | Min.: -128°, Max.: 127° | - | After completing zero point calibration: 0° |
| Steering Angle Sensor | Steering angle sensor | Min.: -3276.8°, Max.: 3276.7° | Turning left: Increases
Turning right: Decreases |
- |
| Zero Point of Steering Angle | Memorized zero value | Min.: -3276.8°, Max.: 3276.7° | - | After steering angle sensor zero point calibration: 0° |
| Lateral G | Lateral G | Min.: -25.10 m/s2, Max.: 24.90 m/s2 | - | During turning: Changes in proportion with acceleration |
| Forward and Rearward G | Forward and backward G | Min.: -25.10 m/s2, Max.: 24.90 m/s2 | - | During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Value | Yaw rate value | Min.: -128°/s, Max.: 127°/s | - | During turning: Changes in proportion with yaw |
| Steering Angle Value | Steering angle value | Min.: -3276.8°, Max.: 3276.7° | - | During steering operation: Changes in proportion with steering wheel rotation |
| Stop Light Relay | Stop light control relay | ON or OFF | ON: Stop light control relay on
OFF: Stop light control relay off |
w/ Downhill assist control or dynamic radar cruise control |
| Slip Indicator Light | Slip indicator light | ON or OFF | ON: Indicator light on
OFF: Indicator light off |
- |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FR Wheel Acceleration | Front wheel RH acceleration | Min.: -200.84 m/s2, Max.: 199.27 m/s2 | - | During deceleration/acceleration: Changes continuously |
| FL Wheel Acceleration | Front wheel LH acceleration | Min.: -200.84 m/s2, Max.: 199.27 m/s2 | - | During deceleration/acceleration: Changes continuously |
| RR Wheel Acceleration | Rear wheel RH acceleration | Min.: -200.84 m/s2, Max.: 199.27 m/s2 | - | During deceleration/acceleration: Changes continuously |
| RL Wheel Acceleration | Rear wheel LH acceleration | Min.: -200.84 m/s2, Max.: 199.27 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Stop Light Relay Output | Stop light control relay | ON or OFF | ON: Relay output on
OFF: Relay output off |
w/ Downhill assist control or dynamic radar cruise control |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | ON or OFF | ON: During control | - |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | ON or OFF | ON: During control | - |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | ON or OFF | ON: During control | - |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | ON or OFF | ON: During control | - |
| BA Ctrl Status | BA control status | ON or OFF | ON: During control | - |
| PBA Ctrl Status | PBA control status | ON or OFF | ON: During control | w/ Pre-collision System |
| TRC(TRAC) Ctrl Status | TRC control status | ON or OFF | ON: During control | - |
| TRC(TRAC) Engine Ctrl Status | TRC engine control status | ON or OFF | ON: During control | - |
| TRC(TRAC) Brake Ctrl Status | TRC brake control status | ON or OFF | ON: During control | - |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | ON or OFF | ON: During control | - |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | ON or OFF | ON: During control | - |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | ON or OFF | ON: During control | - |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | ON or OFF | ON: During control | - |
| Engine Revolutions | Engine speed | Min.: 0 rpm, Max.: 65535 rpm | Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Real Engine Torque | Real engine torque | Min.: -1024.0 Nm, Max.: 1023.0 Nm | - | - |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%, Max.: 128.0% | Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Solenoid Relay | ABS solenoid relay | ON or OFF | ON: ABS solenoid relay on
OFF: ABS solenoid relay off |
- |
| ECB Motor Relay | ABS motor relay | ON or OFF | ON: ABS motor relay on
OFF: ABS motor relay off |
ECB: Electronically Controlled Brake |
| TR(A)C/VSC Solenoid (SM2) | Master cut solenoid (SM2) | ON or OFF | ON: Operates | - |
| TR(A)C/VSC Solenoid (SM1) | Master cut solenoid (SM1) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SFRH) | ABS solenoid (SFRH) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SFRR) | ABS solenoid (SFRR) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SFLH) | ABS solenoid (SFLH) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SFLR) | ABS solenoid (SFLR) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SRRH) | ABS solenoid (SRRH) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SRRR) | ABS solenoid (SRRR) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SRLH) | ABS solenoid (SRLH) | ON or OFF | ON: Operates | - |
| ABS Solenoid (SRLR) | ABS solenoid (SRLR) | ON or OFF | ON: Operates | - |
| FR Speed Open | Front speed sensor RH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| FL Speed Open | Front speed sensor LH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| RR Speed Open | Rear speed sensor RH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| RL Speed Open | Rear speed sensor LH open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| EFI Communication Open | ECM communication open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Yaw Rate Open | Yaw rate sensor open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Deceleration Open | Acceleration sensor open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Steering Open | Steering angle sensor open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| BS1 Voltage Value | +BS voltage value | Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11 to 14 V | Changes in proportion to battery voltage |
| MT Voltage Value | Motor voltage value | Min.: 0.00 V, Max.: 20.00 V | - | - |
| TRC/VSC Off Mode | TRC/VSC off mode | Normal, TRC OFF, Unknown or VSC OFF | TRC OFF: TRC off mode
Unknown: Unspecified VSC OFF: VSC off mode |
- |
| Number of DTC | Number of DTC recorded | Min.: 0, Max.: 255 | - | - |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| M/C Pressure Sensor Noise | Master cylinder pressure sensor noise detection | Error or Normal | Error: Malfunction
Normal: Normal |
- |
| Brake Pedal Switch Open | Brake pedal load sensing switch open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| EFI Communication Invalid | ECM communication invalid detection | Error or Normal | Error: Invalid
Normal: Normal |
- |
| Master Cylinder Pressure | Master cylinder pressure sensor pressure | Min.: 0.00 Mpa, Max.: 23.28 Mpa | Brake pedal depressed: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 Mpa |
- |
| Master Cylinder Sensor Temperature | Master cylinder pressure sensor temperature | Min.: -80°C (-112°F), Max.: 175°C (347°F) | - | Displays current master cylinder temperature |
| Motor Power Supply Voltage | Motor power source voltage | Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11 to 14 V | Changes in proportion to battery voltage |
| Solenoid Power Supply Voltage | Solenoid power supply voltage | Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11 to 14 V | Changes in proportion to battery voltage |
| Stop Light Relay State for ECU Control | Stop light control relay (for ECU control) | ON or OFF | ON: Stop light control relay operating
OFF: Stop light control relay not operating |
- |
| Engine Stop by Stop and Start System | Engine stopped by stop and start system status | ON or OFF | ON: Engine stopped by stop and start control
OFF: Engine not stopped by stop and start control |
This item is displayed on the GTS but is not used |
| Solenoid State for ECU Control | Solenoid (for ECU control) status | ON or OFF | ON: Solenoid relay operating
OFF: Solenoid relay not operating |
- |
| Motor State for ECU Control | Motor (for ECU control) status | ON or OFF | ON: Motor relay operating
OFF: Motor relay not operating |
- |
| Operation History of IG OFF while Vehicle is moving | History of ignition switch turned off when vehicle is in motion | ON or OFF | ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
OFF: No history |
- |
| Master Cylinder Pressure Sensor Power Supply Open | Master cylinder pressure sensor power supply voltage status | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Solenoid Power Supply Open | Solenoid power supply voltage status | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Motor Power Supply Open | Motor power supply voltage status | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Stop Switch Open | Momentary interruption (open circuit) status in the wire harness between the skid control ECU (brake actuator assembly) and the stop light switch assembly | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed.
Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON/OFF | Can be observed on the combination meter assembly |
| Brake Warning Light | Brake warning light | Warning light ON/OFF | Can be observed on the combination meter assembly |
| Downhill Assist Control Light | Downhill assist control indicator light | Indicator light ON/OFF | ·
Can be observed on the combination meter assembly ·
for AWD |
| Buzzer | Meter buzzer | Buzzer ON/OFF | Buzzer can be heard |
| Solenoid Relay | ABS solenoid relay | Relay ON/OFF | - |
| Motor Relay | ABS motor relay | Relay ON/OFF | Operating sound of motor can be heard |
| Stop Light Relay | Stop light control relay | Relay ON/OFF | ·
Stop lights come on ·
w/ Downhill assist control or dynamic radar cruise control |
| ABS Solenoid (SRLR) | ABS solenoid (SRLR) | Solenoid ON/OFF | - |
| ABS Solenoid (SRLH) | ABS solenoid (SRLH) | Solenoid ON/OFF | - |
| ABS Solenoid (SRRR) | ABS solenoid (SRRR) | Solenoid ON/OFF | - |
| ABS Solenoid (SRRH) | ABS solenoid (SRRH) | Solenoid ON/OFF | - |
| ABS Solenoid (SFLR) | ABS solenoid (SFLR) | Solenoid ON/OFF | - |
| ABS Solenoid (SFLH) | ABS solenoid (SFLH) | Solenoid ON/OFF | - |
| ABS Solenoid (SFRR) | ABS solenoid (SFRR) | Solenoid ON/OFF | - |
| ABS Solenoid (SFRH) | ABS solenoid (SFRH) | Solenoid ON/OFF | - |
| VSC/TRC Solenoid (SMR) | Master cut solenoid (SM2) | Solenoid ON/OFF | - |
| VSC/TRC Solenoid (SMF) | Master cut solenoid (SM1) | Solenoid ON/OFF | - |
| TRC(TRAC) OFF Indicator Light | Multi-information display (TRC OFF message) | Display (message) ON/OFF | Can be observed on the combination meter assembly |
| VSC OFF Indicator Light | VSC OFF indicator light | Indicator light ON/OFF | Can be observed on the combination meter assembly |
| Slip Indicator Light | Slip indicator light | Indicator light ON/OFF | Can be observed on the combination meter assembly |
| EBS Relay | Emergency brake signal operation | Relay ON/OFF | - |
| ABS Solenoid | ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH) | Solenoid SRLR/SRLH/SRRR/SRRH/SFLR/SFLH/SFRR/SFRH | Operation sound of solenoid (clicking sound) can be heard |
| VSC/TRC(TRAC) Solenoid | Master cut solenoid (SM1, SM2) | Solenoid SRMF/SRMR/SRCF/SRCR/SMF/SMR/SPFR/SPFL | Operation sound of solenoid (clicking sound) can be heard |