Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0097123 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B271269N08
3.24,0.667 3.656,0.938 0.417,0.271 3.333,0.698 3.792,0.896 0.458,0.198 10 false F66

a.

Disconnect the F66 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F66-1 (+B) - F66-5 (GND) Input GR - W-B Battery Always 11 to 14 V +B
F66-2 (IG) - F66-5 (GND) Input R - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
F66-3 (KSW) - F66-5 (GND) Input GR - W-B Unlock warning switch signal No door control transmitter assembly in ignition key cylinder 10 kΩ or higher
·

B2780

·

Key SW


Door control transmitter assembly in ignition key cylinder Below 1 Ω
F66-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the F66 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F66-8 (IND) - F66-5 (GND) Output GR - W-B Security indicator signal No door control transmitter assembly in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Door control transmitter assembly in ignition key cylinder (immobiliser system unset) Below 1 V
F66-9 (D) - F66-5 (GND) Input/Output SB - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
F66-4 (ANT1) - F66-5 (GND) Input/Output BE - W-B Transponder key amplifier power source No door control transmitter assembly in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder Pulse generation
(See waveform 1)
F66-15 (ANT2) - F66-5 (GND) Input/Output L - W-B Transponder key amplifier communication signal No door control transmitter assembly in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder Pulse generation
(See waveform 2)
F66-12 (EFII) - F66-5 (GND) Input W - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
-
F66-13 (EFIO) - F66-5 (GND) Output B - W-B ECM output signal Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Measurement Condition
Item Content
Tester Connection F66-4 (ANT1) - F66-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N02
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Measurement Condition
Item Content
Tester Connection F66-15 (ANT2) - F66-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F66-12 (EFII) - F66-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F66-13 (EFIO) - F66-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 1AR-FE)


A247842N36
2.208,0.417 2.604,0.646 0.396,0.229 5.833,0.427 6.229,0.656 0.396,0.229 2.323,0.438 2.667,0.625 0.344,0.188 10 false C1 5.906,0.448 6.25,0.635 0.344,0.188 10 false A43

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
C1-16 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C1-50 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C1-49 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A43-1 (BATT) - C1-16 (E1) Input GR - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
A43-3 (+B2) - C1-16 (E1) Input R - BR Power source of ECM Ignition switch ON 11 to 14 V -
A43-2 (+B) - C1-16 (E1) Input G - BR Power source of ECM Ignition switch ON 11 to 14 V -
A43-29 (IMO) - C1-16 (E1) Output W - BR Transponder key ECU assembly communication output Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
A43-28 (IMI) - C1-16 (E1) Input B - BR Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C01
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection A43-29 (IMO) - C1-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection A43-28 (IMI) - C1-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 2GR-FKS)


A247842N37
5.688,0.281 6.115,0.573 0.427,0.292 2.042,0.302 2.479,0.573 0.438,0.271 5.781,0.333 6.24,0.531 0.458,0.198 10 false A43 2.167,0.344 2.625,0.542 0.458,0.198 10 false C1

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
C1-53 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C1-51 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C1-20 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A43-1 (BATT) - C1-53 (E1) Input GR - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V -
A43-3 (+B2) - C1-53 (E1) Input R - BR Power source of ECM Ignition switch ON 11 to 14 V -
A43-2 (+B) - C1-53 (E1) Input G - BR Power source of ECM Ignition switch ON 11 to 14 V -
A43-45 (IMO) - C1-53 (E1) Output W - BR Transponder key ECU assembly communication output Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
A43-59 (IMI) - C1-53 (E1) Input B - BR Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C01
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection A43-45 (IMO) - C1-53 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection A43-59 (IMI) - C1-53 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON