Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


B271001N29
3.354,0.229 3.729,0.458 0.375,0.229 3.417,0.25 3.729,0.427 0.313,0.177 10 false F49

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F49-6 (AGND) - Body ground - W - Body ground Transponder key amplifier ground Always Below 1 Ω -
F49-7 (TXCT) - F49-6 (AGND) Input L - W Immobiliser communication input Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
F49-8 (CODE) - F49-6 (AGND) Output G - W Immobiliser communication output Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
F49-10 (VC5) - F49-6 (AGND) Input B - W Transponder key amplifier power supply Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F49-7 (TXCT) - F49-6 (AGND) Input L - W Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



F49-8 (CODE) - F49-6 (AGND) Output G - W Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
F49-10 (VC5) - F49-6 (AGND) Input B - W Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F49-7 (TXCT) - F49-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B345737N03
2.771,0.792 3.229,0.99 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F49-8 (CODE) - F49-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F49-10 (VC5) - F49-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B340022N27
4.99,0.292 5.417,0.521 0.427,0.229 1.552,0.26 1.979,0.49 0.427,0.229 3.25,0.292 3.677,0.521 0.427,0.229 1.656,0.292 2.115,0.49 0.458,0.198 10 false F10 5.094,0.313 5.552,0.51 0.458,0.198 10 false F13 3.344,0.313 3.802,0.51 0.458,0.198 10 false F12

a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F13-10 (+B) - F13-11 (E) Input GR- W-B +B power supply Always 11 to 14 V -
F13-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F10-3 (IG1D) - F13-11 (E) Output G - W-B Ignition power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V -
F13-14 (TXCT) - F13-12 (AGND) Output L - W Signal output to transponder key amplifier Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F13-13 (CODE) - F13-12 (AGND) Input G - W Signal input from transponder key amplifier Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
F13-15 (VC5) - F13-12 (AGND) Output B- W Transponder key amplifier power supply Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
F13-12 (AGND) - Body ground - W - Body ground Transponder key amplifier ground Always Below 1 Ω
F13-19 (IND) - F13-11 (E) Output GR - W-B Security indicator output Engine switch off → on (IG) Pulse generation → Below 2 V -
F10-7 (EFII) - F13-11 (E)*1 Input W - W-B EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Engine switch off 11 to 14 V
·

B2799*2

·

B279986*3

·

B279A*2

·

B279A12*3

·

EFI Code Receive

·

Engine Start Request


F10-6 (EFIO) - F13-11 (E)*1 Output B - W-B EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Engine switch off 11 to 14 V

*1: w/o Rear Seat Heater

*2: for 1AR-FE

*3: for 2GR-FKS



e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F13-14 (TXCT) - F13-12 (AGND) Output L - W Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F13-13 (CODE) - F13-12 (AGND) Input G - W Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch
HINT:

Remove the transmitter battery before performing this inspection.


Pulse generation
(See waveform 2)
F13-15 (VC5) - F13-12 (AGND) Output B - W Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)
F10-7 (EFII) - F13-11 (E)*1 Input W - W-B EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 4)
·

B2799*2

·

B279986*3

·

B279A*2

·

B279A12*3

·

EFI Code Receive

·

Engine Start Request


F10-6 (EFIO) - F13-11 (E)*1 Output B - W-B EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 5)

*1: w/o Rear Seat Heater

*2: for 1AR-FE

*3: for 2GR-FKS



f.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F13-14 (TXCT) - F13-12 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B345737N04
2.771,0.792 3.229,0.99 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F13-13 (CODE) - F13-12 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F13-15 (VC5) - F13-12 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


iv.

Waveform 4 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F10-7 (EFII) - F13-11 (E)*
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

*: w/o Rear Seat Heater



v.

Waveform 5 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F10-6 (EFIO) - F13-11 (E)*
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

*: w/o Rear Seat Heater





CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Rear Seat Heater)


B278917N31
3.396,0.156 3.792,0.385 0.396,0.229 3.469,0.188 3.792,0.365 0.323,0.177 10 false F67

a.

Disconnect the F67 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F67-1 (+B) - Body ground Input Y - Body ground +B power supply Always 11 to 14 V B2789
F67-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the F67 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F67-3 (EFII) - F67-5 (GND) Input W - BR EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Engine switch off 11 to 14 V
·

B2799*1

·

B279986*2

·

B279A*1

·

B279A12*2

·

EFI Code Receive

·

Engine Start Request


F67-4 (EFIO) - F67-5 (GND) Output B - BR EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Engine switch off 11 to 14 V
F67-3 (EFII) - F67-5 (GND) Input W - BR EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
F67-4 (EFIO) - F67-5 (GND) Output B - BR EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)

*1: for 1AR-FE

*2: for 2GR-FKS



e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F67-3 (EFII) - F67-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F67-4 (EFIO) - F67-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


B118684N52
3.458,0.188 3.833,0.406 0.375,0.219 3.531,0.208 3.854,0.375 0.323,0.167 10 false F54

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F54-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F54-3 (IGE) - F54-1 (GND) Input V - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operates when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


F54-4 (SLP1) - F54-1 (GND) Output LG - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked* 11 to 14 V → Below 1.5 V Sensor Value
F54-6 (IG2) - F54-1 (GND) Input R - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V B2788
F54-7 (B) - Body ground Input B - Body ground Constant power supply Always 11 to 14 V B2788

HINT:

*: The steering locks when any door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F54-3 (IGE) - F54-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off






CHECK ECM (for 1AR-FE)


A247842N34
2.531,0.354 2.927,0.594 0.396,0.24 5.906,0.354 6.302,0.594 0.396,0.24 2.646,0.385 2.948,0.542 0.302,0.156 10 false C1 5.979,0.385 6.281,0.542 0.302,0.156 10 false A43

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A43-3 (+B2) - C1-16 (E1) Input R - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A43-2 (+B) - C1-16 (E1) Input G - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A43-46 (MREL) - C1-50 (E01) Input B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V -
A43-1 (BATT) - C1-16 (E1) Input GR - BR +B power supply Always 11 to 14 V -
C1-50 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C1-16 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C1-49 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C1-29 (+BM) - C1-16 (E1) Input R - BR +B power supply Always 11 to 14 V
A43-29 (IMO) - C1-16 (E1) Output W - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication output Engine switch off 11 to 14 V -
A43-29 (IMO) - C1-16 (E1) Output W - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A43-28 (IMI) - C1-16 (E1) Input B - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication input Engine switch off 11 to 14 V -
A43-28 (IMI) - C1-16 (E1) Input B - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A43-29 (IMO) - C1-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A43-28 (IMI) - C1-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ECM (for 2GR-FKS)


A247842N35
2.531,0.354 2.927,0.594 0.396,0.24 5.906,0.354 6.302,0.594 0.396,0.24 2.656,0.385 2.958,0.542 0.302,0.156 10 false C1 5.979,0.385 6.5,0.656 0.521,0.271 10 false A43

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A43-3 (+B2) - C1-53 (E1) Input R - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A43-2 (+B) - C1-53 (E1) Input G - BR Ignition power supply Engine switch on (IG) 11 to 14 V -
A43-46 (MREL) - C1-51 (E01) Input B - W-B Ignition power supply Engine switch on (IG) 11 to 14 V -
A43-1 (BATT) - C1-53 (E1) Input GR - BR +B power supply Always 11 to 14 V -
C1-51 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C1-53 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C1-20 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A43-8 (+BM) - C1-53 (E1) Input B - BR +B power supply Always 11 to 14 V
A43-45 (IMO) - C1-53 (E1) Output W - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication output Engine switch off 11 to 14 V -
A43-45 (IMO) - C1-53 (E1) Output W - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A43-59 (IMI) - C1-53 (E1) Input B - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication input Engine switch off 11 to 14 V -
A43-59 (IMI) - C1-53 (E1) Input B - BR ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A43-45 (IMO) - C1-53 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A43-59 (IMI) - C1-53 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected