Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296068 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the S18 forward recognition camera connector.



E256359E71
2.104,0.76 2.5,0.99 0.396,0.229 2.188,0.802 2.646,1 0.458,0.198 10 false S18

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S18-7 (IGB) - S18-10 (GND) R - W-B Power source Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
S18-1 (HTR) - S18-10 (GND) BR - W-B Forward recognition with heater hood sub-assembly operation signal Engine switch on (IG)
Forward recognition with heater hood sub-assembly not operating
11 to 14 V
Engine switch on (IG)
Forward recognition with heater hood sub-assembly operating
Below 1 V
S18-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S18-5 (CA1P) - S18-10 (GND) R - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
S18-11 (CA1N) - S18-10 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
S18-6 (CANH) - S18-10 (GND) B - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
S18-12 (CANL) - S18-10 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between S18-5 (CA1P) and S18-10 (GND)
Between S18-6 (CANH) and S18-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between S18-11 (CA1N) and S18-10 (GND)
Between S18-12 (CANL) and S18-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.