Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296068 FORWARD RECOGNITION CAMERA SYSTEM J

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

E256368E91
0.385,0.896 1.813,1.146 1.427,0.25 10 false from IG1 NO. 3 Relay 2.813,1.073 3.573,1.292 0.76,0.219 10 false IG1 NO. 3 5.292,0.917 5.75,1.115 0.458,0.198 10 false IGB 5.281,1.938 5.74,2.135 0.458,0.198 10 false GND 5.052,1.833 5.292,2.021 0.24,0.188 10 false 10 5.115,0.802 5.229,1.01 0.115,0.208 10 false 7 4.792,2.656 6.646,2.865 1.854,0.208 10 false Forward Recognition Camera 4.781,2.49 5.24,2.688 0.458,0.198 10 false S18

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380142C40
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.583,0.208 2.042,0.448 0.458,0.24 10 false S18 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the S18 forward recognition camera connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S18-7 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Connect the S18 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
A380142C41
1.49,0.167 1.906,0.427 0.417,0.26 1.698,1.802 1.792,1.438 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.583,0.219 1.948,0.438 0.365,0.219 10 false S18 1.563,1.823 2.021,2.021 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the S18 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S18-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the S18 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR