Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296066 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) U

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the S18 forward recognition camera connector.



E256359E71
2.104,0.76 2.5,0.99 0.396,0.229 2.188,0.802 2.646,1 0.458,0.198 10 false S18

a.

Disconnect the S18 forward recognition camera connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S18-7 (IGB) - S18-10 (GND) R - W-B Power source Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
S18-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the S18 forward recognition camera connector.


d.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S18-5 (CA1P) - S18-10 (GND) R - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
S18-11 (CA1N) - S18-10 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
S18-6 (CANH) - S18-10 (GND) B - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
S18-12 (CANL) - S18-10 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between S18-5 (CA1P) and S18-10 (GND)
Between S18-6 (CANH) and S18-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between S18-11 (CA1N) and S18-10 (GND)
Between S18-12 (CANL) and S18-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781E44
3.385,0.115 3.833,0.354 0.448,0.24 3.458,0.156 4.073,0.354 0.615,0.198 10 false F128

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F128-7 (B) - F128-28 (GND) R - W-B Power source Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
F128-23 (SPSW) - F128-28 (GND) V - W-B Steering pad switch signal
(Lane departure alert main switch signal)
Engine switch off
Lane departure alert main switch off
1 MΩ or higher
Engine switch off
Lane departure alert main switch on
228 to 252 Ω
F128-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F128-8 (CA1P) - F128-28 (GND) B - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
F128-9 (CA1N) - F128-28 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
F128-10 (CA2H) - F128-28 (GND) G - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
F128-11 (CA2L) - F128-28 (GND) W - W-B CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between F128-8 (CA1P) - F128-28 (GND)
Between F128-10 (CA2H) - F128-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between F128-9 (CA1N) - F128-28 (GND)
Between F128-11 (CA2L) - F128-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.