Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296066 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1AAC  Vehicle Information Unmatched  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the vehicle information received from the ECM. If the vehicle information stored in the forward recognition camera is different from that stored in the ECM, DTC C1AAC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAC Vehicle Information Unmatched 2 seconds after the engine switch is turned on (IG), the vehicle information received from the ECM and that stored in the forward recognition camera do not match.
·

CAN communication system

·

Forward recognition camera

·

ECM



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:

This DTC is stored when the vehicle information stored in the forward recognition camera and that stored in the ECM do not match. If the forward recognition camera or ECM has been replaced, check if a forward recognition camera or ECM from another vehicle was used.


PROCEDURE

1.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

The forward recognition camera communicates with the ECM via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U0100 is not output A
DTC U0100 is output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (2WD/4WD) Vehicle information 2WD, 4WD or Unknown 2WD: for 2WD
4WD: for AWD
Unknown: Vehicle information not confirmed
-
Vehicle Information (Conv/HV) Vehicle information Conv, HV or Unknown Conv: Conventional
HV: Hybrid vehicle
Unknown: Vehicle information not confirmed
-
Chassis > Front Recognition Camera > Data List
Tester Display
Vehicle Information (2WD/4WD)
Vehicle Information (Conv/HV)
50003 386 10,11
HINT:
·

The vehicle information stored in the forward recognition camera is displayed on the Data List.

·

If the vehicle information stored in the forward recognition camera is different from the actual vehicle specifications, the vehicle information stored in the forward recognition camera may be incorrect. Check for DTCs and replace the forward recognition camera if necessary.

·

If the vehicle information stored in the forward recognition camera matches the actual vehicle specifications, the installed ECM is incompatible. Replace the ECM with a correct one.




Result:
Result Proceed to
Vehicle information stored in forward recognition camera and actual vehicle specifications do not match A
Vehicle information stored in forward recognition camera and actual vehicle specifications match B



A

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

3.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 2 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AAC is not output A
DTC C1AAC is output B



A

B

REPLACE FORWARD RECOGNITION CAMERA