Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _060169 PRE-COLLISION _0296083 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

This DTC is stored when the driving support ECU assembly cannot receive signals from the forward recognition camera or millimeter wave radar sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1002 Lost Communication with Gateway Module After the engine switch is turned on, communication between the driving support ECU assembly and any of the following components is abnormal for 2 seconds or more
·

Forward recognition camera

·

Millimeter wave radar sensor assembly


·

CAN bus main line, CAN bus branch line or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

No. 5 CAN junction connector



WIRING DIAGRAM

B429439E19
0.094,1.833 1.49,2.198 1.396,0.365 10 false Millimeter Wave Radar Sensor Assembly 0.094,1.667 0.552,1.865 0.458,0.198 10 false A81 5.229,2.969 7.125,3.156 1.896,0.188 10 false Driving Support ECU Assembly 5.229,2.802 5.688,3 0.458,0.198 10 false F128 0.052,4.156 4.031,4.354 3.979,0.198 10 false Forward Recognition Camera 0.052,3.979 0.51,4.177 0.458,0.198 10 false S18 0.906,3.083 1.521,3.281 0.615,0.198 10 false CANH 0.938,3.833 1.552,4.031 0.615,0.198 10 false CANL 1.365,3.083 1.521,3.281 0.156,0.198 10 false 6 1.344,3.625 1.656,3.823 0.313,0.198 10 false 12 2.771,4.156 5.042,4.427 2.271,0.271 10 false No. 5 CAN Junction Connector 2.771,3.979 3.229,4.177 0.458,0.198 10 false F111 3.219,3.094 3.5,3.271 0.281,0.177 10 false 9 3.156,3.625 3.469,3.823 0.313,0.198 10 false 20 5.792,1.927 5.948,2.125 0.156,0.198 10 false 8 5.792,2.469 5.948,2.667 0.156,0.198 10 false 9 4.094,1.906 4.344,2.115 0.25,0.208 10 false 10 4.083,2.448 4.396,2.646 0.313,0.198 10 false 21 0.917,0.771 1.531,0.969 0.615,0.198 10 false CA1P 0.927,1.51 1.542,1.708 0.615,0.198 10 false CA1N 5.958,2.01 6.573,2.208 0.615,0.198 10 false CA1P 5.958,2.552 6.573,2.75 0.615,0.198 10 false CA1N 1.375,0.771 1.531,0.969 0.156,0.198 10 false 5 3.146,0.771 3.396,0.969 0.25,0.198 10 false 11 1.365,1.302 1.521,1.5 0.156,0.198 10 false 6 3.146,1.302 3.458,1.5 0.313,0.198 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE (MALFUNCTION CONFIRMATION)
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
C334337C30
1.49,0.656 1.948,0.896 0.458,0.24 1.198,1.406 1,0.625 true 1.073,1.417 0.781,0.885 true 2.042,1.396 2.302,0.667 true 0.813,2.406 1.073,1.677 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.688 2.031,0.885 0.458,0.198 10 false F128 0.615,0.521 1.229,0.719 0.615,0.198 10 false CA1P 0.396,0.802 1.01,1 0.615,0.198 10 false CA1N 0.458,2.344 1.073,2.542 0.615,0.198 10 false GND 2.344,0.573 2.958,0.771 0.615,0.198 10 false B
*a Component with harness connected
(Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F128-8 (CA1P) - F128-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω:
Short circuit between bus lines
70 Ω or more:
Open circuit in a main bus line or driving support ECU assembly branch line
F128-8 (CA1P) - F128-28 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
F128-9 (CA1N) - F128-28 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
F128-8 (CA1P) - F128-7 (B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
F128-9 (CA1N) - F128-7 (B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short



Result:
Result Proceed to
OK A
NG (Open circuit in main line or Driving support ECU assembly branch line) B
NG (Short circuit between main lines) C
NG (Short to +B or ground) D



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

3.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)

C

8.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)

D

12.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 2 seconds or more.




c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

B

3.CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
A380143C38
1.563,0.198 1.979,0.427 0.417,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false F128 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F128 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-8 (CA1P) - F128-9 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


HINT:

If the resistance is between 108 and 132 Ω, there may be an open in a CAN bus main line. If the value is 132 Ω or more, there may be an open in a CAN bus branch line between the No. 5 CAN junction connector and the driving support ECU assembly or a connector may be disconnected.



c.

Connect the F128 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR OPEN IN CAN BUS MAIN LINES (NO. 5 CAN JUNCTION CONNECTOR)

NG

7.CHECK FOR OPEN IN CAN BUS BRANCH LINES (NO. 5 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)
4.CHECK FOR OPEN IN CAN BUS MAIN LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.
B427446C86
1.49,0.156 1.938,0.396 0.448,0.24 2.375,0.396 2.219,1.073 true 2.208,1.448 2.323,1.823 true 2.531,1.073 2.844,0.625 true 2.771,1.729 2.542,1.427 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.573,0.198 2.031,0.396 0.458,0.198 10 false F111 2.25,0.208 2.698,0.396 0.448,0.188 10 false CANH 2.219,1.844 2.625,2.042 0.406,0.198 10 false CANL 2.885,0.531 3.344,0.719 0.458,0.188 10 false CA1P 2.813,1.677 3.271,1.875 0.458,0.198 10 false CA1N
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)


Disconnect the F111 No. 5 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-9 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Forward Recognition Camera
F111-11 (CA1P) - F111-22 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Millimeter Wave Radar Sensor Assembly



c.

Connect the F111 No. 5 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)

C

6.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
a.
A380142C39
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.604,0.24 1.979,0.448 0.375,0.208 10 false S18 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the S18 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S18-6 (CANH) - S18-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Connect the S18 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

6.CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C26
1.479,0.167 1.875,0.406 0.396,0.24 1.313,1.792 1.448,1.26 true 1.615,1.26 1.823,1.792 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.198 1.938,0.427 0.375,0.229 10 false A81 1.146,1.813 1.76,2.01 0.615,0.198 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A81 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-5 (CA1P) - A81-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Connect the A81 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

7.CHECK FOR OPEN IN CAN BUS BRANCH LINES (NO. 5 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)
a.
A380143C38
1.563,0.198 1.979,0.427 0.417,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false F128 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F128 driving support ECU assembly connector.


b.
B427446C87
1.49,0.156 1.938,0.396 0.448,0.24 2.375,1.073 2.76,0.458 true 2.677,1.792 2.375,1.438 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.573,0.198 2.031,0.396 0.458,0.198 10 false F111 2.813,0.354 3.302,0.531 0.49,0.177 10 false CA1P 2.729,1.729 3.188,1.927 0.458,0.198 10 false CA1N
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)


Disconnect the F111 No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F111-10 (CA1P) - F128-8 (CA1P) Cable disconnected from negative (-) battery terminal Below 1 Ω
F111-21 (CA1N) - F128-9 (CA1N) Cable disconnected from negative (-) battery terminal Below 1 Ω



d.

Connect the F111 No. 5 CAN junction connector.


e.

Connect the F128 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 5 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE (NO. 5 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

8.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)
a.
A380142C39
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.604,0.24 1.979,0.448 0.375,0.208 10 false S18 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the S18 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S18-6 (CANH) - S18-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Connect the S18 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

9.CHECK FOR SHORT BETWEEN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT BETWEEN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.
B427446C88
1.479,0.146 1.927,0.375 0.448,0.229 2.781,0.885 2.542,1.073 true 2.531,1.438 2.771,1.635 true 2.719,0.479 2.375,1.083 true 2.313,0.313 2.208,1.073 true 2.656,1.823 2.375,1.427 true 2.292,1.885 2.208,1.438 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.052,0.135 2.615,0.313 0.563,0.177 10 false CANH*b 2.042,1.906 2.573,2.094 0.531,0.188 10 false CANL*b 2.76,0.385 3.302,0.573 0.542,0.188 10 false CA1P*d 2.823,0.802 3.375,0.969 0.552,0.167 10 false CA1P*c 2.698,1.792 3.229,1.99 0.531,0.198 10 false CA1N*d 2.813,1.573 3.365,1.74 0.552,0.167 10 false CA1N*c 1.573,0.177 2.031,0.375 0.458,0.198 10 false F111
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly
*d to Driving Support ECU Assembly


Disconnect the F111 No. 5 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-9 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Forward Recognition Camera
F111-11 (CA1P) - F111-22 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Millimeter Wave Radar Sensor Assembly
F111-10 (CA1P) - F111-21 (CA1N) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving Support ECU Assembly



c.

Connect the F111 No. 5 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C
NG (Driving Support ECU Assembly Branch Line) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

C

10.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

11.CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
10.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C26
1.479,0.167 1.875,0.406 0.396,0.24 1.313,1.792 1.448,1.26 true 1.615,1.26 1.823,1.792 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.198 1.938,0.427 0.375,0.229 10 false A81 1.146,1.813 1.76,2.01 0.615,0.198 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A81 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-5 (CA1P) - A81-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Connect the A81 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

11.CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
a.
A380143C38
1.563,0.198 1.979,0.427 0.417,0.229 2.323,0.958 2.479,0.208 true 2.479,0.969 2.729,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false F128 2.51,0.073 3.052,0.302 0.542,0.229 10 false CA1P 2.76,0.313 3.302,0.542 0.542,0.229 10 false CA1N
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F128 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-8 (CA1P) - F128-9 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Connect the F128 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)

12.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the S18 forward recognition camera connector.

B427441C13
1.74,0.542 2.135,0.781 0.396,0.24 4.896,0.417 5.26,0.646 0.365,0.229 2.354,1.427 2.729,1.281 true 2.344,1.74 2.719,1.865 true 4.625,0.698 4.99,1.104 true 5.802,1.698 6.125,1.927 true 4.063,0.208 4.375,0.365 0.313,0.156 10 false *1 1.302,0.198 1.615,0.354 0.313,0.156 10 false *a 1.823,0.573 2.281,0.771 0.458,0.198 10 false S18 4.969,0.448 5.427,0.646 0.458,0.198 10 false F25 2.781,1.208 3.396,1.406 0.615,0.198 10 false CANH 2.781,1.802 3.396,2 0.615,0.198 10 false CANL 4.385,0.625 4.719,0.823 0.333,0.198 10 false CG 6.177,1.875 6.51,2.073 0.333,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S18-6 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
S18-12 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
S18-6 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S18-12 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



c.

Connect the S18 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

13.CHECK FOR SHORT IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
13.CHECK FOR SHORT IN CAN BUS LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the F111 No. 5 CAN junction connector.

B427445C21
1.75,0.49 2.188,0.729 0.438,0.24 5.031,0.448 5.385,0.677 0.354,0.229 2.521,0.552 2.365,1.344 true 2.51,2.177 2.365,1.646 true 2.938,0.771 2.51,1.344 true 2.938,1.25 2.646,1.344 true 2.938,1.74 2.656,1.646 true 2.865,2.031 2.51,1.646 true 4.708,0.635 5.094,1.073 true 5.896,1.646 6.229,1.896 true 4.156,0.219 4.469,0.375 0.313,0.156 10 false *1 1.146,0.229 1.458,0.385 0.313,0.156 10 false *a 1.823,0.531 2.281,0.729 0.458,0.198 10 false F111 5.094,0.479 5.552,0.677 0.458,0.198 10 false F25 2.417,0.365 3.031,0.563 0.615,0.198 10 false CANH*b 2.354,2.188 2.969,2.385 0.615,0.198 10 false CANL*b 2.979,0.688 3.594,0.885 0.615,0.198 10 false CA1P*d 2.979,1.156 3.594,1.354 0.615,0.198 10 false CA1P*c 2.917,1.979 3.531,2.177 0.615,0.198 10 false CA1N*d 2.979,1.667 3.594,1.865 0.615,0.198 10 false CA1N*c 4.479,0.573 4.792,0.771 0.313,0.198 10 false CG 6.292,1.844 6.604,2.042 0.313,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Forward Recognition Camera
*c to Millimeter Wave Radar Sensor Assembly *d to Driving Support ECU Assembly



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-9 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward Recognition Camera
F111-20 (CANL) - F25-4 (CG)
F111-9 (CANH) - F25-16 (BAT) 6 kΩ or higher
F111-20 (CANL) - F25-16 (BAT)
F111-11 (CA1P) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly
F111-22 (CA1N) - F25-4 (CG)
F111-11 (CA1P) - F25-16 (BAT) 6 kΩ or higher
F111-22 (CA1N) - F25-16 (BAT)
F111-10 (CA1P) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving Support ECU Assembly
F111-21 (CA1N) - F25-4 (CG)
F111-10 (CA1P) - F25-16 (BAT) 6 kΩ or higher
F111-21 (CA1N) - F25-16 (BAT)



c.

Connect the F111 No. 5 CAN junction connector.


Result:
Result Proceed to
OK A
NG (Forward Recognition Camera Main Line) B
NG (Millimeter Wave Radar Sensor Assembly Main Line) C
NG (Driving Support ECU Assembly Branch Line) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA)

C

14.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

D

15.CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the A81 millimeter wave radar sensor assembly connector.

B427442C15
1.833,0.385 2.219,0.604 0.385,0.219 5.031,0.396 5.375,0.615 0.344,0.219 1.344,1.885 1.771,1.573 true 2,1.563 2.188,2.094 true 4.552,0.656 5.094,1.115 true 5.896,1.708 6.198,1.958 true 4.115,0.177 4.427,0.333 0.313,0.156 10 false *1 1.292,0.188 1.604,0.344 0.313,0.156 10 false *a 1.906,0.417 2.365,0.615 0.458,0.198 10 false A81 5.094,0.427 5.552,0.625 0.458,0.198 10 false F25 4.313,0.594 4.625,0.792 0.313,0.198 10 false CG 6.25,1.906 6.708,2.104 0.458,0.198 10 false BAT 0.969,1.844 1.427,2.042 0.458,0.198 10 false CA1P 2.042,2.125 2.5,2.323 0.458,0.198 10 false CA1N
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-5 (CA1P) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A81-6 (CA1N) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A81-5 (CA1P) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A81-6 (CA1N) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



c.

Connect the A81 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

15.CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the F128 driving support ECU assembly connector.

B427443C12
1.865,0.479 2.302,0.698 0.438,0.219 5.219,0.385 5.604,0.625 0.385,0.24 2.552,1.271 2.698,0.667 true 2.677,1.281 3.198,0.823 true 5.292,1.083 4.938,0.677 true 6.385,2.031 6.031,1.688 true 4.344,0.177 4.656,0.333 0.313,0.156 10 false *1 1.927,0.51 2.344,0.688 0.417,0.177 10 false F128 0.771,0.198 1.083,0.354 0.313,0.156 10 false *a 5.302,0.427 5.635,0.604 0.333,0.177 10 false F25 2.521,0.51 3.135,0.708 0.615,0.198 10 false CA1P 3.135,0.667 3.75,0.865 0.615,0.198 10 false CA1N 4.708,0.604 5.323,0.802 0.615,0.198 10 false CG 6.427,1.979 6.802,2.167 0.375,0.188 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-8 (CA1P) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F128-9 (CA1N) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F128-8 (CA1P) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F128-9 (CA1N) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



c.

Connect the F128 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)