Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _060169 PRE-COLLISION _0296083 PRE-COLLISION SYSTEM J

PRE-COLLISION  PRE-COLLISION SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the driving support ECU assembly when the engine switch is on (IG).

WIRING DIAGRAM

E256368E94
0.385,0.896 1.813,1.146 1.427,0.25 10 false from IG1 NO. 3 Relay 2.823,1.063 3.573,1.292 0.75,0.229 10 false IG1 NO. 3 5.281,0.906 5.74,1.104 0.458,0.198 10 false B 5.281,1.938 5.74,2.135 0.458,0.198 10 false GND 5.052,1.833 5.292,2.021 0.24,0.188 10 false 28 5.115,0.802 5.229,1.01 0.115,0.208 10 false 7 4.781,2.667 6.906,2.906 2.125,0.24 10 false Driving Support ECU Assembly 4.781,2.49 5.24,2.688 0.458,0.198 10 false F128

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
A380143C36
1.573,0.198 2.01,0.438 0.438,0.24 1.26,0.958 0.896,0.354 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false F128 0.781,0.25 0.938,0.448 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F128 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F128-7 (B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the F128 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
A380143C37
1.594,0.198 2.031,0.427 0.438,0.229 2.281,1.813 2.479,1.281 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.667,0.229 2.125,0.427 0.458,0.198 10 false F128 1.958,1.74 2.344,1.948 0.385,0.208 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F128 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-28 (GND) - Body ground Always Below 1 Ω



c.

Connect the F128 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR