Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever DTCs are detected, the blind spot monitor sensor stores the current vehicle (sensor) state as freeze frame data.



CHECK FREEZE FRAME DATA


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the blind spot monitor system on.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.


f.

According to the display on the GTS, read the freeze frame data for the selected DTC.

Body Electrical > Blind Spot Monitor Master
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator LH turning on OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated



-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator LH flashing OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on

-

Vehicle detected by rear crossing traffic alert function



-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R
-
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.7 deg, Max.: Over 12.6 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.6 degrees or more, "Over 12.6" is displayed and when it is -12.7 degrees or less, "Under -12.7" is displayed
Yaw Rate Sensor Yaw rate sensor Min.: Under -125 deg/s, Max.: 124.612 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-
Body Electrical > Blind Spot Monitor Slave
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator RH turning on OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated



-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator RH flashing OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on

-

Vehicle detected by rear crossing traffic alert function



-
Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: Buzzer sounding
-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Buzzer Input Circuit Voltage Buzzer Input Circuit Voltage Min.: 0 V, Max.: 25.5 V Engine switch on (IG): 11 to 14 V -
Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R
-
Reverse (Only for MT) Not supported OFF or ON - -
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.7 deg, Max.: Over 12.6 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.6 degrees or more, "Over 12.6" is displayed and when it is -12.7 degrees or less, "Under -12.7" is displayed
Yaw Rate Sensor Yaw rate sensor Min.: Under -125 deg/s, Max.: 124.612 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-


CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the freeze frame data.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the blind spot monitor system on.


d.

Turn the GTS on.


e.

Clear the DTCs and freeze frame data.