Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109515 BLIND SPOT MONITOR SYSTEM U

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch State of the Blind spot monitor system OFF or ON OFF: Blind spot monitor system off
ON: Blind spot monitor system on
-
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator LH turning on OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated



-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator LH flashing OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on

-

Vehicle detected by rear crossing traffic alert function



-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R
-
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch Incompl or Compl Incompl: Inspection not completed
Compl: Inspection completed
-
Beam Axis Inspection Completeness Flag Completion of beam axis adjustment Incompl or Compl Incompl: Adjustment not completed
Compl: Adjustment completed
Changes to "Compl" when blind spot monitor beam axis adjustment has been finished
Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.7 deg, Max.: Over 12.6 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.6 degrees or more, "Over 12.6" is displayed and when it is -12.7 degrees or less, "Under -12.7" is displayed
RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF or ON OFF: w/o RCTA function
ON: w/ RCTA function
-
Master Side RCTA Function Switches the RCTA function on and off OFF or ON ON: RCTA function on
OFF: RCTA function off
-
Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz -
Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0 %, Max.: 100 % Always: 50 % -
Yaw Rate Sensor Yaw rate sensor Min.: Under -125 deg/s, Max.: 124.612 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-
Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator RH turning on OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

During initial check

-

Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated



-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator RH flashing OFF or ON

OFF: Any state except "ON" state

ON: Either of the following state

-

Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on

-

Vehicle detected by rear crossing traffic alert function



-
Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: Buzzer sounding
-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA
-
Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 V
-
Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R
-
Reverse (Only for MT) Not Supported OFF or ON - -
Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag Completion of beam axis adjustment Incompl or Compl Incompl: Adjustment not completed
Compl: Adjustment completed
Changes to "Compl" when blind spot monitor beam axis adjustment has been finished
Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.7 deg, Max.: Over 12.6 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.6 degrees or more, "Over 12.6" is displayed and when it is -12.7 degrees or less, "Under -12.7" is displayed
RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF or ON OFF: w/o RCTA function
ON: w/ RCTA function
-
Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz -
Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0 %, Max.: 100 % Always: 50 % -
Buzzer Control Frequency Frequency of RCTA buzzer (blind spot monitor buzzer) when sounding Min.: 1000 Hz, Max.: 2400 Hz Always: 2000 Hz -
Yaw Rate Sensor Yaw rate sensor Min.: Under -125 deg/s, Max.: 124.612 deg/s Turning right: -125 to 0 deg/s
Turning left: 0 to 124.612 deg/s
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-