Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › KNOCK SENSOR › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0303261 KNOCK SENSOR A

2GR-FKS ENGINE CONTROL  KNOCK SENSOR  INSTALLATION  


PROCEDURE

Hide 89615 1.INSTALL KNOCK CONTROL SENSOR

HINT:

Perform "Inspection After Repair" after replacing a knock control sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A372516C01
0.24,2.427 3.271,4.583 3.031,2.156 0.24,3.49 3.25,3.49 false 0.323,2.479 0.698,2.719 0.375,0.24 12 false *A 0.333,3.531 0.708,3.771 0.375,0.24 12 false *B 0.833,3.51 1.146,3.708 0.313,0.198 10 false *b 0.792,2.438 1.104,2.635 0.313,0.198 10 false *a 2.542,2.521 2.854,2.719 0.313,0.198 10 false *c 2.542,3.635 2.854,3.833 0.313,0.198 10 false *c 0.74,2.917 1.052,3.115 0.313,0.198 10 false *d 0.719,4 1.031,4.198 0.313,0.198 10 false *e 1.052,4.177 1.365,4.375 0.313,0.198 10 false *f 1.042,3.063 1.354,3.26 0.313,0.198 10 false *f 1.021,2.781 1.333,2.979 0.313,0.198 10 false *g 1.031,3.875 1.344,4.073 0.313,0.198 10 false *g
*A for Bank 1
*B for Bank 2
*a View A
*b View B
*c Top
*d Engine Front
*e Engine Rear
*f 5°
*g 10°
V100135

Engine Front
V100136

View A
V100137

View B


Temporarily install the 2 knock control sensors to the cylinder block sub-assembly with the 2 bolts so that the knock control sensor installation position is as shown in the illustration.

NOTICE:
·

If a knock control sensor has been struck or dropped, replace it.

·

Make sure that the knock control sensor is installed in the correct position.




b.
A369369C01
1.938,1.833 2.146,1.833 2.146,1.833 2.146,1.333 true 1.792,1.5 1.948,1.667 0.156,0.167 10 true A 2.438,0.698 2.594,0.865 0.156,0.167 10 true B 1.323,0.417 1.479,0.583 0.156,0.167 10 true *a 1.792,1.74 1.948,1.906 0.156,0.167 10 true *b
*a Torque Wrench Fulcrum Length
*b 10 mm Union Nut Wrench


Tighten the bolt (A).

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Using a 10 mm union nut wrench, tighten the bolt (B).

Torque:
Specified tightening torque : 20 N*m (204 kgf*cm, 15 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.6 N*m (179 kgf*cm, 13 ft.*lbf)




d.

Connect the 2 knock control sensor connectors.


Hide 3.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a knock control sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION