Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296068 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAE  Heater Circuit  


DESCRIPTION

The forward recognition camera controls the flow of current to the forward recognition with heater hood sub-assembly.

If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE Heater Circuit
Either of the following conditions is met after 2 seconds have elapsed since the engine switch was turned on (IG):
·

Short to +B detected in the forward recognition with heater hood sub-assembly circuit for 1 second or more cumulatively

·

Open or short to ground detected in the forward recognition with heater hood sub-assembly circuit for 5 seconds or more


·

Forward recognition with heater hood sub-assembly

·

Forward recognition camera

·

Wire harness or connector



WIRING DIAGRAM

A398326E03
0.115,0.698 3.177,0.896 3.063,0.198 10 false from IG1 NO. 2 Relay 2.271,0.854 2.906,1.104 0.635,0.25 10 false ECU-IG 3.042,1.063 5.021,1.458 1.979,0.396 10 false Forward Recognition with Heater Hood Sub-assembly 3.573,0.688 4.031,0.885 0.458,0.198 10 false IG1 4.146,0.688 4.604,0.885 0.458,0.198 10 false HTR 3.396,0.594 3.552,0.792 0.156,0.198 10 false 1 4.5,0.583 4.656,0.781 0.156,0.198 10 false 2 5.344,0.583 5.5,0.781 0.156,0.198 10 false 1 5.531,0.688 5.99,0.885 0.458,0.198 10 false HTR 3.031,0.906 3.948,1.104 0.917,0.198 10 false S19 4.99,1.917 5.448,2.115 0.458,0.198 10 false S15 5,2.073 6.865,2.302 1.865,0.229 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AAE is not output A
DTC C1AAE is output B



A

B

2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
2.INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
a.

Turn the engine switch off.


b.
A401973C03
1.698,0.188 2.125,0.438 0.427,0.25 1.688,1.854 1.823,1.26 true 2.188,1.854 2.042,1.271 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.802,0.229 2.26,0.427 0.458,0.198 10 false S19 1.563,1.885 2.021,2.083 0.458,0.198 10 false HTR 2.135,1.885 2.594,2.083 0.458,0.198 10 false IG1
*a Component without harness connected
(Forward Recognition with Heater Hood Sub-assembly)


Disconnect the S19 forward recognition with heater hood sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S19-1 (IG1) - S19-2 (HTR) Engine switch off 38 to 42 Ω



d.

Connect the S19 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

NG

REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A401974C03
1.552,0.208 1.938,0.448 0.385,0.24 1.125,1.125 1.552,1.219 true 0.198,0.167 0.51,0.323 0.313,0.156 10 false *a 1.625,0.25 2.083,0.448 0.458,0.198 10 false S19 0.875,1.042 1.333,1.24 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Forward Recognition with Heater Hood Sub-assembly)


Disconnect the S19 forward recognition with heater hood sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S19-1 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1.5 V



c.

Connect the S19 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the S19 forward recognition with heater hood sub-assembly connector.


b.

Disconnect the S15 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S19-2 (HTR) - S15-1 (HTR) Always Below 1 Ω
S19-2 (HTR) or S15-1 (HTR) - Body ground Always 10 kΩ or higher



d.

Connect the S15 forward recognition camera connector.


e.

Connect the S19 forward recognition with heater hood sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)