Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the fluid temperature into a resistance value for use by the ECM.

C274654E01
1.833,1.458 1.531,1.896 false 0.313,0.646 1.844,0.844 1.531,0.198 10 Resistance 1.01,3.823 1.958,4.031 0.948,0.208 10 Temperature 1.917,1.385 3.104,1.594 1.188,0.208 10 Acceptable range

The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.

The ECM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic).
·

Short in ATF temperature sensor circuit

·

Transmission wire (ATF temperature sensor)

·

Wiring harness connector

·

ECM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input ATF temperature sensor resistance is more than 156 kΩ for 0.5 seconds or more, and either of the following conditions is met (1-trip detection logic):
·

Condition (A): 314 seconds or more have elapsed after the engine start when engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.

·

Condition (B): 10 seconds or more have elapsed after the engine start when engine coolant temperature and intake air temperature are more than -29.375°C (- 20.875°F).


·

Open in ATF temperature sensor circuit

·

Transmission wire (ATF temperature sensor)

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor circuit. The ATF temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and can detect an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will illuminate the MIL and store a DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:

The ATF temperature can be checked on the GTS display.


WIRING DIAGRAM

C240445E07
5.833,4.292 6.479,4.479 0.646,0.188 10 false ECM 5.323,1.396 5.865,1.563 0.542,0.167 10 false THO1 0.667,2.927 2.313,3.292 1.646,0.365 10 false ATF Temperature Sensor 3.802,1.198 4.344,1.365 0.542,0.167 10 false 13 3.802,2.333 4.344,2.5 0.542,0.167 10 false 12 5.823,4.125 6.365,4.292 0.542,0.167 10 false C1 2.531,2.333 3.073,2.5 0.542,0.167 10 false 17 2.521,1.219 3.063,1.385 0.542,0.167 10 false 18 5.313,2.531 5.854,2.698 0.542,0.167 10 false ETHO 4.979,2.417 5.521,2.583 0.542,0.167 10 false 119 4.958,1.292 5.5,1.458 0.542,0.167 10 false 120 0.781,3.396 2.135,3.583 1.354,0.188 10 false Automatic Transaxle 2.802,3.406 3.802,3.76 1,0.354 10 false Wiring Harness Connector 3.792,1.406 4.208,1.563 0.417,0.156 10 false C2 3.802,2.531 4.083,2.688 0.281,0.156 10 false C2 2.563,1.417 2.844,1.573 0.281,0.156 10 false A 2.573,2.542 2.854,2.698 0.281,0.156 10 false A 1.969,1.271 2.469,1.49 0.5,0.219 10 false THO1 2.031,2.427 2.344,2.594 0.313,0.167 10 false E2 3.417,1.281 3.958,1.448 0.542,0.167 10 false OIL 3.448,2.427 3.781,2.594 0.333,0.167 10 false E2

CAUTION / NOTICE / HINT

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall speed test: Approximately 80°C (176°F)

·

While engine is cold:

Equal to ambient temperature


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or short circuited
Powertrain > Engine > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406
HINT:

When DTC P0712 is output and the GTS indicates 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the GTS indicates -40°C (-40°F), there is an open circuit.

Measure the resistance between terminal THO1 (OT) and body ground.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit

HINT:

If the circuit related to the ATF temperature sensor becomes open, P0713 is stored immediately (in 0.5 seconds). When P0713 is stored, P0711 cannot be detected.

It is not necessary to inspect the circuit when P0711 is stored.




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR CIRCUIT)
a.
C240434C05
0.24,0.958 0.698,1.177 0.458,0.219 0.844,2.667 1.198,2.01 false 1.281,2.01 1.813,2.552 false 0.26,0.198 0.573,0.396 0.313,0.198 10 false *a 1.813,2.552 2.323,2.76 0.51,0.208 10 false THO1 0.385,0.99 0.781,1.167 0.396,0.177 10 false C1 0.625,2.688 1.135,2.896 0.51,0.208 10 false ETHO
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-120 (THO1) - C1-119 (ETHO) Always 79 Ω to 156 kΩ
C1-120 (THO1) - Body ground and other terminals Always 10 kΩ or higher
C1-119 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the connector from the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-120 (THO1) - C2-13 (OIL) Always Below 1 Ω
C1-119 (ETHO) - C2-12 (E2) Always Below 1 Ω
C1-120 (THO1) or C2-13 (OIL) - Body ground and other terminals Always 10 kΩ or higher
C1-119 (ETHO) or C2-12 (E2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
a.
C133212C01
2.385,0.854 2.667,1.083 0.281,0.229 1.917,1.031 2.281,0.729 false 2.052,1.135 2.271,1.281 false 2.302,0.625 2.698,0.771 0.396,0.146 10 THO1 2.302,1.219 2.635,1.417 0.333,0.198 10 E2 2.49,0.885 2.677,1.063 0.188,0.177 10 A 0.667,0.365 0.906,0.521 0.24,0.156 10 *a
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-17 (E2) - A-18 (THO1) Always 79 Ω to 156 kΩ
A-17 (E2) - Body ground and other terminals Always 10 kΩ or higher
A-18 (THO1) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range with the ATF temperature shown in the table below, the driveability of the vehicle may decrease.


ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ


Result:
Proceed to
OK
NG



OK

NG

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)