Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0798  Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3)  


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL3 circuit while driving and shifting gears (SL3 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).
·

Open or short in shift solenoid valve SL3 circuit

·

Shift solenoid valve SL3

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores a DTC. The ECM also performs the fail-safe function and turns the other normal shift solenoid valves on or off (in case of an open or short circuit, the ECM stops sending current to the circuit).

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

WIRING DIAGRAM

C239277E32
5.677,4.229 6.104,4.417 0.427,0.188 10 false ECM 5.083,1.521 5.51,1.708 0.427,0.188 10 false SL3+ 5.083,2.927 5.51,3.115 0.427,0.188 10 false SL3- 3.625,1.531 4.052,1.719 0.427,0.188 10 false SL3+ 3.625,2.938 4.052,3.125 0.427,0.188 10 false SL3- 1.625,2.24 2.604,2.573 0.979,0.333 10 false Shift Solenoid Valve SL3 1.021,3.49 2.583,3.677 1.563,0.188 10 false Automatic Transaxle 3.031,3.479 4.031,3.833 1,0.354 10 false Wiring Harness Connector 3.115,1.531 3.542,1.719 0.427,0.188 10 false SL3+ 3.115,2.938 3.542,3.125 0.427,0.188 10 false SL3- 2.313,1.531 2.74,1.719 0.427,0.188 10 false SL3+ 2.313,2.938 2.74,3.125 0.427,0.188 10 false SL3- 5.385,4.229 5.74,4.385 0.354,0.156 10 false C1 4.813,1.531 5.083,1.688 0.271,0.156 10 false 11 4.813,2.927 5.083,3.083 0.271,0.156 10 false 10 2.802,2.563 3.094,2.719 0.292,0.156 10 false 15 4.083,1.167 4.375,1.333 0.292,0.167 10 false 19 4.083,2.563 4.365,2.729 0.281,0.167 10 false 18 4.073,2.76 4.354,2.917 0.281,0.156 10 false C2 4.063,1.375 4.344,1.531 0.281,0.156 10 false C2 2.844,2.76 3.177,2.917 0.333,0.156 10 false A 2.844,1.375 3.198,1.531 0.354,0.156 10 false A 2.802,1.177 3.083,1.333 0.281,0.156 10 false 16

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL3 CIRCUIT)
a.
C240434C08
0.24,0.958 0.698,1.177 0.458,0.219 0.979,2.438 1.073,1.729 false 1.135,1.729 1.688,2.385 false 0.271,0.188 0.615,0.385 0.344,0.198 10 false *a 0.385,0.99 0.781,1.167 0.396,0.177 10 false C1 1.625,2.438 2.052,2.625 0.427,0.188 10 false SL3+ 0.771,2.458 1.198,2.646 0.427,0.188 10 false SL3-
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-11 (SL3+) - C1-10 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
C1-11 (SL3+) - Body ground and other terminals Always 10 kΩ or higher
C1-10 (SL3-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the connector from the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-11 (SL3+) - C2-19 (SL3+) Always Below 1 Ω
C1-10 (SL3-) - C2-18 (SL3-) Always Below 1 Ω
C1-11 (SL3+) or C2-19 (SL3+) - Body ground and other terminals Always 10 kΩ or higher
C1-10 (SL3-) or C2-18 (SL3-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SL3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SL3)
a.
C133212C05
2.333,0.76 2.646,0.99 0.313,0.229 1.417,0.979 2.208,1.365 false 1.521,0.865 2.281,0.573 false 2.25,1.292 2.646,1.521 0.396,0.229 10 SL3+ 2.344,0.448 2.76,0.646 0.417,0.198 10 SL3- 2.438,0.792 2.625,0.969 0.188,0.177 10 A 0.667,0.323 0.896,0.552 0.229,0.229 10 *a
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (SL3+) - A-15 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
A-16 (SL3+) - Body ground Always 10 kΩ or higher
A-15 (SL3-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE SL3
4.INSPECT SHIFT SOLENOID VALVE SL3
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Shift Solenoid Valve SL3


Remove shift solenoid valve SL3.

When Not Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Not Using the Engine Support Bridge)>DISASSEMBLY

When Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Using the Engine Support Bridge)>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG