Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to the system description for DTC P2714.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P2714

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic)
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C239277E33
5.656,4.354 6.083,4.542 0.427,0.188 10 false ECM 5.104,1.229 5.531,1.417 0.427,0.188 10 false SLT+ 5.104,2.635 5.531,2.823 0.427,0.188 10 false SLT- 3.615,1.25 4.042,1.438 0.427,0.188 10 false SLT+ 3.615,2.646 4.042,2.833 0.427,0.188 10 false SLT- 1.604,1.927 2.542,2.26 0.938,0.333 10 false Shift Solenoid Valve SLT 1.125,3.417 2.479,3.604 1.354,0.188 10 false Automatic Transaxle 3.052,3.427 4.052,3.781 1,0.354 10 false Wiring Harness Connector 3.094,1.25 3.521,1.438 0.427,0.188 10 false SLT+ 3.094,2.646 3.521,2.833 0.427,0.188 10 false SLT- 2.302,1.25 2.729,1.438 0.427,0.188 10 false SLT+ 2.302,2.646 2.729,2.833 0.427,0.188 10 false SLT- 5.656,4.198 5.938,4.354 0.281,0.156 10 false C1 4.802,1.24 5,1.396 0.198,0.156 10 false 15 4.802,2.635 5,2.792 0.198,0.156 10 false 14 2.854,2.552 2.979,2.719 0.125,0.167 10 false 7 2.802,1.167 3,1.323 0.198,0.156 10 false 12 4.125,2.552 4.26,2.719 0.135,0.167 10 false 7 4.073,1.167 4.271,1.323 0.198,0.156 10 false 15 2.844,2.76 3.125,2.917 0.281,0.156 10 false A 2.844,1.375 3.125,1.531 0.281,0.156 10 false A 4.063,2.76 4.344,2.917 0.281,0.156 10 false C2 4.073,1.365 4.354,1.521 0.281,0.156 10 false C2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SLT CIRCUIT)
a.
C233488C42
1.469,0.323 1.958,0.615 0.49,0.292 1.458,1.052 1.688,1.75 1.688,1.75 1.844,1.75 false 1.385,1.052 1.156,1.76 1.156,1.76 1,1.76 false 0.104,0.063 0.344,0.26 0.24,0.198 10 false *a 0.646,1.677 1.042,1.844 0.396,0.167 10 false SLT- 1.896,1.667 2.292,1.833 0.396,0.167 10 false SLT+ 1.615,0.385 2.104,0.646 0.49,0.26 10 false C1
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-15 (SLT+) - C1-14 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C1-15 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
C1-14 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the connector from the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-15 (SLT+) - C2-15 (SLT+) Always Below 1 Ω
C1-14 (SLT-) - C2-7 (SLT-) Always Below 1 Ω
C1-15 (SLT+) or C2-15 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
C1-14 (SLT-) or C2-7 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SLT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SLT)
a.
C133212C06
2.386,1.064 2.741,1.214 0.355,0.149 10 SLT+ 2.386,0.345 2.718,0.495 0.332,0.149 10 SLT- 1.783,0.715 2.349,0.433 false 1.912,0.964 2.356,1.15 false 0.66,0.297 0.992,0.447 0.332,0.149 10 *a 2.307,0.656 2.794,0.948 0.487,0.292 2.483,0.712 2.671,0.894 0.187,0.182 10 A
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-12 (SLT+) - A-7 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
A-12 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
A-7 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE SLT
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.

When Not Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Not Using the Engine Support Bridge)>DISASSEMBLY

When Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Using the Engine Support Bridge)>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG