Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2769  Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  P2770  Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  


DESCRIPTION

Shift solenoid valve SL is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2769 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) ECM detects a short in the shift solenoid valve SL circuit when the shift solenoid valve SL is operated (2 trip detection logic).
·

Short in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

Wiring Harness Connector

·

ECM


Comes on DTC stored
P2770 Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) ECM detects an open in the shift solenoid valve SL circuit when the shift solenoid valve SL is not operated (2 trip detection logic).
·

Open in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

Wiring Harness Connector

·

ECM


Comes on DTC stored

Fail-safe function:

If the ECM detects a malfunction, it turns shift solenoid valve SL off.

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the ECM sends a signal to the shift solenoid valve SL to regulate the hydraulic pressure and provide smoother torque converter clutch engagement. The shift solenoid valve SL responds to commands from the ECM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects an open or short in the shift solenoid valve SL circuit, it will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C239278E05
5.677,4.302 6.104,4.479 0.427,0.177 10 false ECM 5.104,1.302 5.344,1.469 0.24,0.167 10 false SL 3.698,1.188 3.938,1.354 0.24,0.167 10 false SL 1.646,2.052 2.531,2.438 0.885,0.385 10 false Shift Solenoid Valve SL 1.115,3.5 2.427,3.677 1.313,0.177 10 false Automatic Transaxle 3.021,3.5 4.01,3.833 0.99,0.333 10 false Wiring Harness Connector 5.677,4.135 5.969,4.292 0.292,0.156 10 false C1 4.083,1.083 4.229,1.26 0.146,0.177 10 false 6 2.781,1.083 2.896,1.26 0.115,0.177 10 false 6 3.063,1.188 3.302,1.354 0.24,0.167 10 false SL 2.427,1.188 2.667,1.354 0.24,0.167 10 false SL 4.896,1.198 5.042,1.375 0.146,0.177 10 false 3 2.76,1.292 3.052,1.448 0.292,0.156 10 false A 4.021,1.302 4.313,1.458 0.292,0.156 10 false C2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL CIRCUIT)
a.
C233488C44
1.469,0.313 1.958,0.604 0.49,0.292 0.542,1.052 0.76,1.75 0.76,1.75 0.927,1.75 false 0.083,0.042 0.323,0.24 0.24,0.198 10 false *a 0.99,1.677 1.385,1.844 0.396,0.167 10 false SL 1.625,0.375 2.333,0.615 0.708,0.24 10 false C1
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-3 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the connector from the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-3 (SL) - C2-6 (SL) Always Below 1 Ω
C1-3 (SL) - Body ground and other terminals Always 10 kΩ or higher
C2-6 (SL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C133212C20
2.302,0.667 2.667,0.969 0.365,0.302 1.906,0.719 2.302,0.354 false 2.354,0.271 2.729,0.51 0.375,0.24 10 SL 0.656,0.302 0.969,0.563 0.313,0.26 10 *a 2.438,0.729 2.625,0.906 0.188,0.177 10 A
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-6 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE SL
4.INSPECT SHIFT SOLENOID VALVE SL
a.
C133217C02
0.203,0.177 0.424,0.335 0.221,0.158 10 *1
*1 Shift Solenoid Valve SL


Remove shift solenoid valve SL.

When Not Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Not Using the Engine Support Bridge)>DISASSEMBLY

When Using the Engine Support Bridge: Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY(When Using the Engine Support Bridge)>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid Connector (SL) - Solenoid Body (SL) 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG