Home › Engine / Hybrid System › 2GR-FKS STARTING › STARTER › from 2016.11
RM3160E _51 Engine / Hybrid System _060163 2GR-FKS STARTING _0300110 STARTER G

2GR-FKS STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.

Remove the nut, and disconnect the field coil lead wire from terminal C.


ii.
A210436C01
1.115,2.844 1.469,2.844 1.469,2.844 1.781,1.729 false 0.24,2.604 0.417,2.604 0.417,2.604 0.656,2.26 false 1.969,1.635 2.292,1.271 2.292,1.271 2.51,1.271 false 0.948,2.75 1.26,2.906 0.313,0.156 10 false *a 2.594,1.188 2.906,1.344 0.313,0.156 10 false *b 0.052,2.51 0.365,2.667 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Moves outward


Connect a battery to the magnet switch as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the repair service starter kit.



b.

Perform a hold-in test.

i.
A210437C01
1.271,2.594 1.51,2.594 1.51,2.594 1.781,1.729 false 1.948,1.625 2.052,1 2.052,1 2.365,1 true 0.26,2.583 0.438,2.583 0.438,2.583 0.635,2.302 false 1.073,2.51 1.385,2.667 0.313,0.156 10 false *a 2.438,0.927 2.75,1.083 0.313,0.156 10 false *b 0.073,2.5 0.385,2.656 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect


While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.

If the clutch pinion gear returns inward, replace the repair service starter kit.



c.

Perform a return test.

i.
A309189C01
1.979,1.646 2.115,0.969 2.115,0.969 2.417,0.969 true 1.229,2.646 1.469,2.646 1.469,2.646 1.781,1.75 false 0.74,2.844 0.74,2.49 false 1.031,2.542 1.344,2.698 0.313,0.156 10 false *a 2.5,0.885 2.813,1.042 0.313,0.156 10 false *b 0.667,2.865 0.979,3.021 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect
V100136

Returns inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the repair service starter kit.



d.

Perform a no-load performance test.

i.

Connect the field coil lead wire to terminal C with the nut. Make sure that the field coil lead wire is not grounded.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A345251C01
0.354,2.302 0.635,2.302 false 1.323,2.948 1.771,2.948 false 2.094,1.448 2.406,1.448 false 1.813,2.854 2.125,3.01 0.313,0.156 10 false *a 2.458,1.344 2.771,1.5 0.313,0.156 10 false *b 0.198,2.188 0.51,2.344 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal 30
*c Starter Body
V100135

Rotates


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

HINT:

If there is no continuity between any segments, replace the starter armature assembly.


a.

Check the commutator appearance.

If the surface is dirty or burnt, restore it with sandpaper (400-grit) or on a lathe.


b.
A295764C10
1.458,1.219 1.729,0.479 1.729,0.479 1.969,0.479 false 0.688,1.573 0.969,1.573 0.969,1.573 1.323,1.302 false 2.042,0.406 2.354,0.563 0.313,0.156 10 false *a 0.531,1.458 0.844,1.615 0.313,0.156 10 false *a
*a Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.
A295765C07
0.813,1.292 1.333,1.292 false 2,1.135 2.25,0.458 2.25,0.458 2.5,0.458 false 0.667,1.208 0.979,1.365 0.313,0.156 10 false *a 2.563,0.375 2.875,0.531 0.313,0.156 10 false *b
*a Segment
*b Starter Armature Core


Check the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A295766C02
2.875,0.938 3.188,1.094 0.313,0.156 10 false *a
*a Length


Using a vernier caliper, measure the commutator length.

Standard Length:

3.1 mm (0.122 in.)


Maximum Length:

3.8 mm (0.150 in.)


If the length is greater than the maximum, replace the starter armature assembly.


Hide 28130 3.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A118276C06
0.427,0.708 0.74,0.865 0.313,0.156 10 false *a
*a Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard Length:

9.0 mm (0.354 in.)


Minimum Length:

4.0 mm (0.157 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.



b.
A118281C08
1.406,0.854 1.24,0.24 1.24,0.24 1.771,0.688 true 1.792,1.01 2.344,0.333 2.344,0.333 2.198,0.75 true 1.073,0.135 1.396,0.333 0.323,0.198 10 false *b 2.375,0.24 2.688,0.438 0.313,0.198 10 false *a
*a Positive (+) Brush
*b Negative (-) Brush


Check the brush insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, replace the starter commutator end frame assembly.



Hide 4.INSPECT STARTER CLUTCH

A081655C06
1.563,0.208 1.875,0.365 0.313,0.156 10 false *a 1.667,1.635 1.979,1.792 0.313,0.156 10 false *b
*a Lock
*b Free


a.

Check the clutch pinion gear.

i.

Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.

If the clutch pinion gear does not operate as specified, replace the starter drive housing assembly.



Hide 28226B 5.INSPECT REPAIR SERVICE STARTER KIT

a.
A295769

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If the plunger does not operate as specified, replace the repair service starter kit.



b.
A079725C07
2.063,1.448 1.542,0.219 1.542,0.219 2.188,0.219 true 1.188,1.948 1.5,1.948 1.5,1.948 1.75,1.625 true 1.01,1.875 1.323,2.031 0.313,0.156 10 false *a 2.271,0.135 2.583,0.292 0.313,0.156 10 false *b
*a Terminal 50
*b Terminal C


Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, repair service starter kit.



c.
A079726C09
1.146,0.385 1.344,0.146 1.344,0.146 1.521,0.146 false 1.427,2.021 1.635,2.021 1.635,2.021 1.885,1.677 true 1.24,1.927 1.552,2.083 0.313,0.156 10 false *a 1.594,0.073 1.906,0.229 0.313,0.156 10 false *b
*a Terminal 50
*b Magnet Switch Body


Check the holding coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 -Magnet switch body Always Below 2 Ω


If the result is not as specified, replace the repair service starter kit.