Home › Engine / Hybrid System › 2GR-FKS STARTING › STARTER › from 2016.11
RM3160E _51 Engine / Hybrid System _060163 2GR-FKS STARTING _0300110 STARTER A

2GR-FKS STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL PLANETARY GEAR

a.
A315339C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter drive housing assembly.


b.

Install the 3 planetary gears to the starter drive housing assembly.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Secure the starter commutator end frame assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
A315340C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the starter armature shaft.


c.
A309041C02
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the washer and bearing shown in the illustration.


d.

Install the starter armature assembly to the starter commutator end frame assembly.


e.
A295762C02
1.552,0.646 1.281,0.646 false 1.115,0.563 1.427,0.719 0.313,0.156 10 false *a
*a Snap Ring Pliers


Using snap ring pliers, install the washer and a new snap ring.

NOTICE:
·

Be sure to install the snap ring in the starter armature shaft groove securely.

·

Do not expand the snap ring excessively.




f.
A058810C10
1.563,0.354 1.875,0.51 0.313,0.156 10 false *a
*a Width


Using a vernier caliper, measure the width of the snap ring end gap as shown in the illustration.

Maximum Width:

5.0 mm (0.197 in.)


If the width is greater than the maximum, replace the snap ring with a new one.


Hide 28132A 3.INSTALL STARTER COMMUTATOR END FRAME COVER

a.
A081178

Install the starter commutator end frame cover to the starter commutator end frame assembly.


Hide 28177 4.INSTALL STARTER ARMATURE PLATE

a.
A073991C16
1.813,0.833 1.542,0.469 1.542,0.469 1.25,0.469 false 0.365,1.125 0.052,0.552 0.052,0.552 0.396,0.552 false 1.063,0.396 1.24,0.708 0.177,0.313 10 false *b 0.438,0.479 0.646,0.698 0.208,0.219 10 false *a
*a Keyway
*b Key


Insert the starter armature plate to the starter yoke assembly.


b.

Align the keyway of the starter armature plate with the key inside the starter yoke assembly, and install the starter armature plate.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

A079727C08
2.01,0.531 1.719,0.208 1.719,0.208 1.333,0.208 false 1.583,0.865 1.042,0.552 1.042,0.552 0.885,0.552 true 0.729,0.469 0.917,0.635 0.188,0.167 10 false *b 1.177,0.104 1.365,0.281 0.188,0.177 10 false *a
*a Rubber
*b Cutout


a.

Align the rubber of the starter commutator end frame assembly with the cutout of the starter yoke assembly.


b.

Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, causing the magnet to break.



Hide 28120 6.INSTALL STARTER YOKE ASSEMBLY

a.
A079728C04
1.552,1.229 1.802,0.979 1.802,0.979 2.031,0.979 false 1.333,1.198 1.146,1.99 1.146,1.99 0.885,1.99 true 2.115,0.896 2.292,1.094 0.177,0.198 10 false *a 0.719,1.896 0.917,2.094 0.198,0.198 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the starter yoke assembly with the cutout of the starter drive housing assembly.


b.

Install the starter yoke assembly with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226B 7.INSTALL REPAIR SERVICE STARTER KIT

a.
A315407C01
2.063,1.167 2.521,1.448 2.521,1.448 2.781,1.448 true 2.854,1.385 3.167,1.542 0.313,0.156 10 false *a
*a Hook
V100135

High-temperature Grease


Apply high-temperature grease to the plunger.


b.

Hang the hook of the plunger on the drive lever.


c.
A315408C01
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the return spring.


d.

Install the return spring to the plunger.


e.

Install the magnet switch to the starter drive housing assembly with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


f.

Connect the field coil lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)