Home › Power Source / Network › 2GR-FKS BATTERY / CHARGING › GENERATOR › from 2016.11
RM3160E _57 Power Source / Network _060166 2GR-FKS BATTERY / CHARGING _0303645 GENERATOR A

2GR-FKS BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A240513

Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A128071

Remove the 3 nuts and generator rear end cover from the generator coil assembly.


Hide 3.REMOVE GENERATOR TERMINAL INSULATOR

a.
A128072

Remove the generator terminal insulator from the generator coil assembly.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A128073

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A128074

Remove the 4 bolts.


b.
A118275C09
2.125,0.771 2.646,0.771 false 0.677,0.594 1.115,0.115 1.115,0.115 1.26,0.115 false 2.688,0.719 3.042,0.99 0.354,0.271 10 false SST 1.313,0.052 1.635,0.323 0.323,0.271 10 false SST 2.552,0.344 2.823,0.604 0.271,0.26 10 false *a 0.125,1.844 0.438,2.042 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, remove the generator coil assembly from the generator rotor assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.
A315469C01
0.844,0.427 1.458,0.427 false 0.677,0.354 0.99,0.51 0.313,0.156 10 false *1
*1 Washer


Remove the washer from the generator rotor assembly.


Hide 27415 6.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.
A315629C01
0.573,2.167 0.927,2.167 false 2.083,2.052 2.083,2.531 false 3.021,1.125 3.021,1.76 true 1.594,0.333 1.854,0.333 1.854,0.333 2.094,0.781 true 1.375,0.229 1.688,0.385 0.313,0.156 10 false *a 1.906,2.594 2.469,2.865 0.563,0.271 10 true SST A 2.802,1.823 3.365,2.094 0.563,0.271 10 true SST A 0.125,2.094 0.688,2.365 0.563,0.271 10 false SST B
*a Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



c.
A194274C07
2.552,1.479 2.708,2.24 2.708,2.24 2.854,2.24 true 2.323,1.094 2.563,0.646 2.563,0.646 2.708,0.646 true 2.906,2.156 3.385,2.333 0.479,0.177 10 false SST A 2.781,0.583 3.292,0.76 0.51,0.177 10 false SST B 1.083,2.948 1.302,3.177 0.219,0.229 10 true *a 1.969,2.042 2.281,2.24 0.313,0.198 10 true *b
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (B) as shown in the illustration.

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.


·

Hold SST (A) tightly during the operation.




d.

Remove SST from the generator pulley with clutch.


e.

Remove the generator pulley with clutch from the rotor shaft.


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A300641

Remove the generator rotor assembly from the generator drive end frame.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A128076

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A128077E01
0.187,0.662 0.485,0.807 0.298,0.145 10 SST 1.308,0.98 0.573,0.778 0.573,0.778 1.249,1.236 false

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)