Home › Power Source / Network › 2GR-FKS BATTERY / CHARGING › GENERATOR › from 2016.11
RM3160E _57 Power Source / Network _060166 2GR-FKS BATTERY / CHARGING _0303645 GENERATOR A

2GR-FKS BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A125191E01
0.179,0.427 0.492,0.623 0.314,0.196 10 SST 1.055,0.948 0.572,0.518 0.572,0.518 0.937,1.085 false

Using SST and a press, install a new generator drive end frame bearing to the generator drive end frame.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A137712C02
2.583,1.052 1.927,0.771 true 2.542,1.531 1.896,1.833 true 1.74,1.76 1.927,1.906 0.188,0.146 10 false *b 1.771,0.667 2.031,0.906 0.26,0.24 10 false *a
*a Tab
*b Cutout


Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.
A396279C01
2.313,1.656 2.854,1.656 false 0.604,0.958 1.146,0.958 false 0.458,0.875 0.771,1.031 0.313,0.156 10 false *1 2.865,1.563 3.177,1.719 0.313,0.156 10 false *2
*1 Generator Rotor Assembly
*2 Generator Drive End Frame


Install the generator rotor assembly to the generator drive end frame.


Hide 27415 3.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Temporarily install the generator pulley with clutch to the rotor shaft.


b.

Secure the generator drive end frame in a vise between aluminum plates.


c.
A315629C01
0.573,2.167 0.927,2.167 false 2.083,2.052 2.083,2.531 false 3.021,1.125 3.021,1.76 true 1.594,0.333 1.854,0.333 1.854,0.333 2.094,0.781 true 1.375,0.229 1.688,0.385 0.313,0.156 10 false *a 1.906,2.594 2.469,2.865 0.563,0.271 10 true SST A 2.802,1.823 3.365,2.094 0.563,0.271 10 true SST A 0.125,2.094 0.688,2.365 0.563,0.271 10 false SST B
*a Rotor Shaft


Place the rotor shaft end into SST (A).

SST
09820-63021  


d.

Fit SST (B) to the generator pulley with clutch.


e.
A315630C02
3.031,4.052 3.031,3.115 true 1.531,2.958 1.719,2.958 1.719,2.958 2.448,3.031 true 2.396,3.656 2.573,3.844 0.177,0.188 10 true *a 2.208,2.229 2.521,2.385 0.313,0.156 10 false *b 1.104,0.323 1.417,0.479 0.313,0.156 10 false *c 1.521,3.802 1.833,3.958 0.313,0.156 10 true *d 1.104,2.885 1.875,3.083 0.771,0.198 10 false SST B 2.833,4.063 3.333,4.271 0.5,0.208 10 false SST A
*a Hold
*b Turn
*c Length of SST 100 mm (3.94 in.)
*d Length of Torque Wrench 400 mm (1.31 ft.)


Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (1.312 ft.)): 64 N*m (653 kgf*cm, 47 ft.*lbf)




f.

Remove SST (A) and (B) from the generator pulley with clutch.


g.

Check that the generator pulley with clutch rotates smoothly.


h.

Remove the generator drive end frame from the vise.


Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.

Place a new washer on the generator rotor assembly.

HINT:

Washer has direction and must be need to put washer chip for bearing side.



b.
A172926C01
1.146,0.344 1.448,0.344 1.448,0.344 1.781,0.635 false 0.938,0.26 1.25,0.417 0.313,0.156 10 false *a
*a 21 mm Socket Wrench


Using a 21 mm socket wrench and press, slowly press the generator coil assembly to install it.


c.
A128074

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C12
2.479,0.74 1.979,0.198 1.979,0.198 1.729,0.198 false 0.917,0.521 0.708,0.198 0.708,0.198 0.458,0.198 false 1.521,0.094 1.833,0.313 0.313,0.219 10 false *a 0.271,0.104 0.583,0.323 0.313,0.219 10 false *a
*a Pin (1.0 mm)


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


b.
A334792C04
1.76,1.073 1.76,1.313 false 1.698,1.333 1.896,1.573 0.198,0.24 10 false *a
*a Pin (1.0 mm)
V100136

Pull out


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly hole.


Hide 6.INSTALL GENERATOR TERMINAL INSULATOR

a.
A128083

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct direction.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.
A386449

Install the generator rear end cover to the generator coil assembly with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.