Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2016.11
RM3160E _59 Vehicle Exterior _019724 EXTERIOR PANELS / TRIM _0109634 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REMOVAL  


PROCEDURE

Hide 76626D 1.REMOVE REAR QUARTER PANEL MUDGUARD LH

Hide 76625D 2.REMOVE REAR QUARTER PANEL MUDGUARD RH

HINT:

Use the same procedure as for the LH side.


Hide 75874 3.DISCONNECT QUARTER PANEL WHEEL OPENING MOULDING LH

a.
B408121C01
1.021,1.031 1.021,1.042 false
V100155

Protective Tape


Apply protective tape around the quarter panel wheel opening moulding LH and rear bumper assembly as shown in the illustration.


b.
B408131

Remove the 2 screws.


c.

Remove the 2 clips.


d.

While pulling the rear bumper assembly, insert a finger between the rear bumper side seal LH and rear bumper assembly and disengage the 4 claws by pushing the area shown in the illustration.

B408122C01
0.792,2.26 1.208,2.146 false 3.021,2.75 3.427,2.979 false 3.208,2.24 3.635,2.188 false 5.417,2.25 5.854,2.156 false 1.083,2.438 1.208,2.563 false 5.323,2.875 5.625,2.896 false 0.49,2.792 0.635,2.698 false 2.781,3.156 3.104,3.083 false 5.031,3.365 5.354,3.406 false 0.333,2.75 0.646,2.948 0.313,0.198 10 false *1 0.927,2.354 1.24,2.552 0.313,0.198 10 false *2 1.24,2.073 1.552,2.271 0.313,0.198 10 false *3 3.573,2.479 3.885,2.677 0.313,0.198 10 false *a 3.125,1.375 3.281,1.573 0.156,0.198 10 true 1 3.115,1.094 3.271,1.292 0.156,0.198 10 true 2 3.083,0.823 3.24,1.021 0.156,0.198 10 true 3 2.969,0.583 3.125,0.781 0.156,0.198 10 true 4 3.667,2.104 3.979,2.302 0.313,0.198 10 false *3 5.906,2.073 6.219,2.271 0.313,0.198 10 false *3 2.844,2.656 3.156,2.854 0.313,0.198 10 false *2 5.146,2.792 5.458,2.99 0.313,0.198 10 false *2 2.615,3.094 2.927,3.292 0.313,0.198 10 false *1 4.854,3.281 5.167,3.479 0.313,0.198 10 false *1
*1 Quarter Panel Wheel Opening Moulding LH *2 Rear Bumper Assembly
*3 Rear Bumper Side Seal LH - -
*a Push - -


NOTICE:

To avoid damaging the claws, do not forcibly pull the quarter panel wheel opening moulding LH.


HINT:

Disengage the claws in the order shown in the illustration.



e.

Disengage the 2 clips to disconnect the quarter panel wheel opening moulding LH from the rear bumper assembly.


Hide 75873 4.DISCONNECT QUARTER PANEL WHEEL OPENING MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 5.REMOVE REAR BUMPER ASSEMBLY

a.
B408123

Remove the 4 screws.


b.
B408124

Remove the 6 clips.


c.
B408125

Disengage the 7 claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



d.

Disconnect the connector.


e.
B408126

Remove the rear bumper assembly.