Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER › from 2016.11
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303759 SHIFT LEVER G

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 33550 1.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/o Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.


a.

Inspect wire harness:

i.
C296588

Disconnect the shift lock control ECU connector.


ii.
C271751C23
1.979,1.281 2.365,0.396 2.365,0.396 2.479,0.396 true 1.99,1.573 2.208,1.948 2.208,1.948 2.302,1.948 true 1.615,1.573 1.448,2.01 1.448,2.01 1.583,2.01 true 2.542,0.333 2.906,0.521 0.365,0.188 10 false STP 1.646,1.927 1.979,2.094 0.333,0.167 10 false ACC 2.365,1.865 2.615,2.042 0.25,0.177 10 false IG 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
6 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
8 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C271751C18
0.729,0.875 0.854,0.875 0.854,0.875 1.396,1.333 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.583,0.813 0.75,1 0.167,0.188 10 false E
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
1 (E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect key interlock solenoid operation signal:

i.
C296588

Connect the shift lock control ECU connector.


ii.
C339731C01
1.896,1.208 2.229,1.813 2.229,1.813 2.531,1.813 true 0.094,0.073 0.406,0.281 0.313,0.208 10 false *a 2.594,1.719 3.115,1.979 0.521,0.26 10 false KLS+
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V


HINT:

Do not disconnect the shift lock control ECU connector.


If the result is not as specified, repair or replace the transmission floor shift assembly.



c.

Inspect shift lock solenoid:

i.
C296589

Disengage the 3 claws to remove the shift lock control ECU from the transmission floor shift assembly.


ii.
C296590

Disconnect the shift lock solenoid connector.


iii.
C197452C17
0.802,1.521 1.365,1.25 false 1.135,1.802 1.594,1.25 false 2.063,1.25 2.615,1.542 false 2.281,1.802 1.844,1.25 false 0.063,0.042 0.271,0.229 0.208,0.188 10 *a 2.677,1.479 2.833,1.677 0.156,0.198 10 P 2.333,1.74 2.542,1.927 0.208,0.188 10 E2 0.771,1.75 1.156,1.938 0.385,0.188 10 SLS- 0.417,1.448 0.833,1.635 0.417,0.188 10 SLS+
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


If the result is not as specified, replace the transmission floor shift assembly.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


If the result is not as specified, replace the transmission floor shift assembly.



Hide 33550 2.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/ Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly.


a.

Inspect wire harness:

i.
C296588

Disconnect the shift lock control ECU connector.


ii.
C296591C01
2.198,1.208 2.646,0.865 2.646,0.865 2.781,0.865 true 2.229,1.531 2.719,1.885 2.719,1.885 2.854,1.885 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 2.823,0.792 3.281,0.99 0.458,0.198 10 false STP 2.906,1.813 3.365,2.01 0.458,0.198 10 false IG
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
6 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
12 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C296591C02
0.542,0.635 0.677,0.635 0.677,0.635 1.615,1.188 true 0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 0.396,0.583 0.656,0.854 0.26,0.271 10 false E
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
3 (E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect shift lock solenoid:

i.
C296589

Disengage the 3 claws to remove the shift lock control ECU from the transmission floor shift assembly.


ii.
C296590

Disconnect the shift lock solenoid connector.


iii.
C197452C17
0.802,1.521 1.365,1.25 false 1.135,1.802 1.594,1.25 false 2.063,1.25 2.615,1.542 false 2.281,1.802 1.844,1.25 false 0.063,0.042 0.271,0.229 0.208,0.188 10 *a 2.677,1.479 2.833,1.677 0.156,0.198 10 P 2.333,1.74 2.542,1.927 0.208,0.188 10 E2 0.771,1.75 1.156,1.938 0.385,0.188 10 SLS- 0.417,1.448 0.833,1.635 0.417,0.188 10 SLS+
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


If the result is not as specified, replace the transmission floor shift assembly.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


If the result is not as specified, replace the transmission floor shift assembly.



Hide 3.INSPECT TRANSMISSION CONTROL SWITCH

a.
C296587

Disconnect the transmission control switch connector.


b.
C271751C19
1.823,1.281 2.208,0.396 2.208,0.396 2.323,0.396 true 1.813,1.573 2.031,1.948 2.031,1.948 2.125,1.948 true 0.958,1.979 1.073,1.979 1.073,1.979 1.458,1.583 true 1.448,1.281 1.281,1.094 1.281,1.094 0.865,1.094 true 1.604,1.281 1.188,0.625 1.188,0.625 0.896,0.625 true 2.167,1.875 2.531,2.063 0.365,0.188 10 false S 0.479,1.021 0.938,1.25 0.458,0.229 10 false SFTD 0.833,1.906 1.26,2.083 0.427,0.177 10 false E 2.396,0.313 2.646,0.49 0.25,0.177 10 false IG 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 0.531,0.563 0.99,0.792 0.458,0.229 10 false SFTU
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever held in "+" Below 1 Ω
Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever held in "-" Below 1 Ω
Shift lever not held in "-" 10 kΩ or higher


If the result is not as specified, replace the transmission floor shift assembly.