Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296316 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on dynamic radar cruise control system operation, the driving support ECU assembly provides warnings to the driver by sounding the skid control buzzer assembly.

DTC C1A4A is stored when a malfunction is detected in the skid control buzzer circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the driving support ECU assembly detects a malfunction in the skid control buzzer circuit for approximately 0.4 seconds or more.
·

Skid control buzzer assembly

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

A389308E28
0.146,0.677 3.208,0.875 3.063,0.198 10 false from IG1 NO. 3 Relay 2.219,0.875 5.281,1.073 3.063,0.198 10 false IG1 NO. 3 3.5,1.073 6.563,1.271 3.063,0.198 10 false A59 3.5,1.24 4.792,1.594 1.292,0.354 10 false Skid Control Buzzer Assembly 3.573,0.698 6.635,0.896 3.063,0.198 10 false IG1 4.24,0.708 4.698,0.938 0.458,0.229 10 false BZ 3.396,0.583 6.458,0.781 3.063,0.198 10 false 2 4.49,0.583 4.708,0.781 0.219,0.198 10 false 1 5.531,0.698 5.99,0.927 0.458,0.229 10 false BZ 5.354,0.594 5.573,0.792 0.219,0.198 10 false 3 5.479,2.083 5.948,2.281 0.469,0.198 10 false F128 5.479,2.25 6.771,2.604 1.292,0.354 10 false Driving Support ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check for DTCs of the pre-collision system.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220
HINT:

The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 36 km/h (22 mph), however the pre-collision system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-collision system, perform troubleshooting of the pre-collision system first.



Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

2.CHECK FOR DTCs (RADAR CRUISE 2)

B

2.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

3.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
3.INSPECT SKID CONTROL BUZZER ASSEMBLY (CONFIRM BUZZER OPERATION)
a.

Turn the engine switch on (IG).


b.

Check that the skid control buzzer assembly sounds.


Result:
Result Proceed to
The skid control buzzer assembly does not sound when the engine switch is on (IG). A
The skid control buzzer assembly sounds continuously when the engine switch is on (IG). B



A

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)

B

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)
a.
A390675C02
0.625,1.24 1,1.51 0.375,0.271 1.938,1.604 2.177,1.979 2.177,1.979 2.448,1.979 true 0.146,0.198 0.458,0.354 0.313,0.156 10 false *a 0.698,1.302 1.156,1.5 0.458,0.198 10 false A59 2.51,1.896 2.969,2.094 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)


Disconnect the A59 skid control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A59-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A59-2 (IG1) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the A59 skid control buzzer assembly connector.


b.

Disconnect the F128 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-1 (BZ) - F128-3 (BZ) Always Below 1 Ω
A59-1 (BZ) or F128-3 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SKID CONTROL BUZZER ASSEMBLY
a.

Remove the skid control buzzer assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER>REMOVAL


b.

Inspect the skid control buzzer assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE SKID CONTROL BUZZER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the A59 skid control buzzer assembly connector.


b.

Disconnect the F128 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-1 (BZ) - F128-3 (BZ) Always Below 1 Ω
A59-1 (BZ) or F128-3 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR