Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0109809 AUTOMATIC TRANSAXLE SYSTEM L

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  PRECAUTION  


EXPRESSIONS OF IGNITION SWITCH


The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)


PRECAUTION FOR DISCONNECTING THE BATTERY CABLE


NOTICE:

When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected:

System Name See Procedure
Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Parking assist monitor system
Panoramic view monitor system
Power door lock control system
Air conditioning system (for Automatic Air Conditioning System)
Air conditioning system (for Manual Air Conditioning System)
Power back door system



PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


NOTICE:
·

If automatic transaxle parts are replaced, perform the following as necessary referring to the table below:

-
-

Initialization of the transaxle compensation code.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION

-

Reset Memory (learned values).

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION

Parts Replacement Compensation Table
Replaced Part Transaxle Compensation Code Road Test Reset Memory (Learned Values)
Automatic Transaxle Assembly Input Necessary Reset
Valve Body Assembly Initialize Necessary Reset
Shift Solenoid Valve SL1 and/or SL2 - Necessary -
Shift Solenoid Valve SL3 and/or SL4 Initialize Necessary Reset
ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Input (Into the new ECM) Necessary Reset
Impossible Initialize Necessary Reset


·

Reset Memory cannot be completed by only disconnecting and reconnecting the cable to the negative (-) battery terminal.




HANDLING PRECAUTIONS


CAUTION:

When using compressed air, always aim away from yourself to prevent Automatic Transmission Fluid (ATF) or kerosene from spraying on your face.


NOTICE:
·

The automatic transaxle is composed of precision-made parts. Careful inspection before reassembly is necessary because even a small nick could cause fluid leakage or affect performance.

·

The procedures are organized so that you work on only one component group at a time. This will help avoid confusion with similar-looking parts of different sub-assemblies being on your workbench at the same time.

·

The component groups are inspected and repaired from the converter housing side.

·

Whenever possible, complete the inspection, repair and reassembly before proceeding to the next component group. If a defect is found in a certain component group during reassembly, inspect and repair this group immediately. If a component group cannot be assembled because parts are being ordered, be sure to keep all parts of the group in a separate container while proceeding with disassembly, inspection, repair and reassembly of other component groups.

·

Use of Toyota Genuine ATF WS is recommended.

·

All disassembled parts should be cleaned, and compressed air should be blown through any fluid passages and holes.

·

Dry all parts with compressed air. Never use cloth.

·

The recommended ATF or kerosene should be used for cleaning.

·

After cleaning, the parts should be arranged in the order they were removed for efficient inspection, repair and reassembly.

·

New discs for the brakes and clutches must be soaked in ATF for at least 15 minutes before reassembly.

·

All oil seal rings, clutch discs, clutch plates, rotating parts, and sliding surfaces should be coated with ATF prior to reassembly.

·

All old gaskets and rubber O-rings must be replaced.

·

Do not apply adhesive cement to gaskets or similar parts.

·

Make sure that the ends of snap rings are not aligned with any cutouts. Make sure that snap rings are correctly installed into the grooves.

·

If a worn bushing is to be replaced, the sub-assembly containing the bushing must also be replaced.

·

Check the thrust bearings and races for wear or damage. Replace them if necessary.

·

Use petroleum jelly to keep parts in place.

·

When working with FIPG material, observe the following:

-

Using a razor blade and a gasket scraper, remove all the old seal packing (FIPG) from the gasket surface.

-

Thoroughly clean all components to remove any loose material.

-

Clean both sealing surfaces with a non-residue solvent.

-

Parts must be reassembled within 10 minutes of application. Otherwise, the seal packing (FIPG) must be removed and reapplied.