The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070513 | Transmission Range Sensor "A" Circuit Open | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The ignition switch is ON and battery voltage is 10.5 V or more. 2.
All of the following signals are OFF simultaneously: -
NSW input signal -
P input signal -
R input signal -
N input signal -
D input signal 3.
60 seconds 4.
2-trip detection logic |
·
Park/neutral position switch assembly ·
Open in park/neutral position switch assembly circuit ·
ECM |
Comes on | DTC stored | SAE Code:
P0705 |
| P070562 | Transmission Range Sensor "A" Signal Compare Failure | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The ignition switch is ON and battery voltage is 10.5 V or more. 2.
Any 2 or more of the following signals are ON simultaneously: -
(NSW, P or N) input signal -
R input signal -
D input signal 3.
2 seconds 4.
2-trip detection logic |
·
Park/neutral position switch assembly ·
Short in park/neutral position switch assembly circuit ·
ECM |
Comes on | DTC stored | SAE Code:
P0705 |
These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will then illuminate the MIL and store a DTC.
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Check the battery voltage is 10.5 V or more.
Turn the ignition switch to ON.
Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each.
Turn the ignition switch off.
Perform steps (1) through (3) again.
Check for DTCs again.
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Disconnect the C14 park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C14-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| C14-1 (RB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C14 park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C14-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| C14-4 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch Assembly) |
Disconnect the C14 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 9 (L) | Shift lever in P or N | Below 1 Ω |
| 1 (RB) - 3 (PL) | Shift lever in P | Below 1 Ω |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| 1 (RB) - 8 (NL) | Shift lever in N | Below 1 Ω |
| 1 (RB) - 7 (DL) | Shift lever in D, S, "+" or "-" | Below 1 Ω |
| 4 (B) - 9 (L) | Shift lever not in P or N | 10 kΩ or higher |
| 1 (RB) - 3 (PL) | Shift lever not in P | 10 kΩ or higher |
| 1 (RB) - 2 (RL) | Shift lever not in R | 10 kΩ or higher |
| 1 (RB) - 8 (NL) | Shift lever not in N | 10 kΩ or higher |
| 1 (RB) - 7 (DL) | Shift lever not in D, S, "+" or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>COMPONENTS
Connect the C14 park/neutral position switch assembly connector.
Disconnect the C1 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-108 (P) - Body ground | ·
Ignition switch ON ·
Shift lever in P |
11 to 14 V |
| C1-107 (R) - Body ground | ·
Ignition switch ON ·
Shift lever in R |
11 to 14 V* |
| C1-140 (N) - Body ground | ·
Ignition switch ON ·
Shift lever in N |
11 to 14 V |
| C1-139 (D) - Body ground | ·
Ignition switch ON ·
Shift lever in D, S, "+" or "-" |
11 to 14 V |
| C1-108 (P) - Body ground | ·
Ignition switch ON ·
Shift lever not in P |
Below 1 V |
| C1-107 (R) - Body ground | ·
Ignition switch ON ·
Shift lever not in R |
Below 1 V |
| C1-140 (N) - Body ground | ·
Ignition switch ON ·
Shift lever not in N |
Below 1 V |
| C1-139 (D) - Body ground | ·
Ignition switch ON ·
Shift lever not in D, S, "+" or "-" |
Below 1 V |
*: The voltage will drop slightly due to the illumination of the back up lights.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION
Disconnect the C14 park/neutral position switch assembly connector.
Disconnect the C1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-4 (B) - C1-106 (NSW) | Always | Below 1 Ω |
| C14-4 (B) or C1-106 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION