Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0109513 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the television camera assembly judges as a result of its self check that the signals or signal lines between the television camera assembly and radio and display receiver assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Television camera assembly power supply failure
·

Harness or connector

·

Television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E288974E55
1.781,0.531 2.24,0.729 0.458,0.198 10 false CA+ 1.677,0.938 2.135,1.135 0.458,0.198 10 false CGND 2.167,0.438 2.479,0.635 0.313,0.198 10 false 11 2.167,0.844 2.479,1.042 0.313,0.198 10 false 23 3.573,0.792 3.885,0.99 0.313,0.198 10 false * 5.146,0.438 5.302,0.635 0.156,0.198 10 false 6 5.146,0.833 5.302,1.031 0.156,0.198 10 false 5 5.354,0.542 5.813,0.74 0.458,0.198 10 false CB+ 5.354,0.938 5.813,1.135 0.458,0.198 10 false CGND 4.938,1.208 5.396,1.406 0.458,0.198 10 false X13 4.927,1.385 6.781,1.646 1.854,0.26 10 false Television Camera Assembly 0.667,1.51 3.521,1.75 2.854,0.24 10 false Radio and Display Receiver Assembly 4.896,2.031 5.885,2.271 0.99,0.24 10 false *: Shielded 0.677,1.313 1.135,1.51 0.458,0.198 10 false F72

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable from the negative (-) battery terminal was disconnected, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F72 radio and display receiver assembly connector.


b.

Disconnect the X13 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-11 (CA+) - X13-6 (CB+) Always Below 1 Ω
F72-23 (CGND) - X13-5 (CGND) Always Below 1 Ω
F72-11 (CA+) - F72-23 (CGND) Always 10 kΩ or higher
F72-11 (CA+) - Body ground Always 10 kΩ or higher
F72-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (CGND, CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (CGND, CA+)
a.

Reconnect the F72 radio and display receiver assembly connector.


b.
E271917C18
1.521,0.188 1.969,0.479 0.448,0.292 1.302,1.813 1.229,1.313 false 0.813,0.771 1.229,1.125 false 1.635,0.25 2.021,0.438 0.385,0.188 10 false F72 1.146,1.823 1.771,2.052 0.625,0.229 10 false CGND 0.5,0.646 1.125,0.875 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F72-11 (CA+) - F72-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY