Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2016.11
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109951 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when the quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Engine running
Blower switch: on
Temperature setting: MAX HOT
Light control switch assembly off
·

Engine coolant temperature: 65°C (149°F) or lower (3 PTC heater relays operating)

·

Engine coolant temperature: 70°C (158°F) or lower (2 PTC heater relays operating)

·

Engine coolant temperature: 75°C (167°F) or lower (1 PTC heater relay operating)


Ambient temperature: 10°C (50°F) or lower

WIRING DIAGRAM

E267041E14
2.125,0.698 2.729,0.969 0.604,0.271 10 false ECU-IG 4.5,0.458 4.771,0.76 0.271,0.302 10 false 2 4.49,0.938 4.813,1.344 0.323,0.406 10 false 3 3.479,0.938 3.76,1.365 0.281,0.427 10 false 5 3.469,0.458 3.802,0.729 0.333,0.271 10 false 1 3.552,1.292 4.708,1.563 1.156,0.271 10 false PTC HTR NO. 1 3.552,2.479 4.875,2.708 1.323,0.229 10 false PTC HTR NO. 2 3.531,3.667 4.833,3.927 1.302,0.26 10 false PTC HTR NO. 3 4.479,2.115 4.688,2.49 0.208,0.375 10 false 3 3.479,1.646 3.688,2.021 0.208,0.375 10 false 1 3.49,2.094 3.698,2.469 0.208,0.375 10 false 5 4.49,1.656 4.698,2.031 0.208,0.375 10 false 2 3.469,2.833 3.677,3.208 0.208,0.375 10 false 1 4.49,3.313 4.698,3.688 0.208,0.375 10 false 3 4.49,2.823 4.698,3.198 0.208,0.375 10 false 2 3.479,3.302 3.688,3.677 0.208,0.375 10 false 5 1.854,1.177 2.885,1.49 1.031,0.313 10 false PTC HTR NO. 1 1.885,2.375 2.917,2.688 1.031,0.313 10 false PTC HTR NO. 2 1.865,3.552 2.958,3.823 1.094,0.271 10 false PTC HTR NO. 3 0.104,0.542 1.479,0.917 1.375,0.375 10 false from IG1 NO. 2 Relay 0.667,1.01 1.51,1.365 0.844,0.354 10 false from Battery 2.906,4.167 3.292,4.385 0.385,0.219 10 false F37 2.917,5.188 3.302,5.396 0.385,0.208 10 false F37 4.479,4.167 4.823,4.417 0.344,0.25 10 false F36 4.479,4.552 4.938,4.833 0.458,0.281 10 false F36 4.479,5.188 4.969,5.375 0.49,0.188 10 false F36 2.99,3.948 3.208,4.229 0.219,0.281 10 false 1 2.99,4.969 3.208,5.25 0.219,0.281 10 false 2 3.302,4.052 3.521,4.333 0.219,0.281 10 false E 3.292,5.073 3.51,5.354 0.219,0.281 10 false E 4.229,5.073 4.448,5.354 0.219,0.281 10 false B 4.229,4.448 4.448,4.729 0.219,0.281 10 false B 4.229,4.052 4.448,4.333 0.219,0.281 10 false B 4.552,3.958 4.771,4.24 0.219,0.281 10 false 1 4.563,4.354 4.781,4.635 0.219,0.281 10 false 3 4.552,4.979 4.771,5.26 0.219,0.281 10 false 2 5.563,3.677 5.885,3.938 0.323,0.26 10 false F80 5.552,3.833 7.104,4.542 1.552,0.708 10 false Air Conditioning Amplifier Assembly 5.583,0.448 5.844,0.833 0.26,0.385 10 false 40 5.656,1.635 6.063,1.938 0.406,0.302 10 false 3 5.583,2.802 6.083,3.188 0.5,0.385 10 false 36 5.854,0.542 6.417,0.802 0.563,0.26 10 false PTC1 5.854,1.74 6.417,2 0.563,0.26 10 false PTC2 5.854,2.938 6.417,3.198 0.563,0.26 10 false PTC3 3.104,5.479 4.698,5.802 1.594,0.323 10 false Quick Heater Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Heater Active Level Quick heater assembly Min.: 0
Max.: 3
-
Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Active Level
50004 121 33
OK:

Heater Active Level changes normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT PTC HEATER RELAY

NG

2.INSPECT PTC HEATER RELAY
a.

Remove the PTC heater relays.


b.
E287491C10
1.073,1.135 1.292,0.833 1.292,0.833 1.448,0.833 false 0.792,0.865 0.844,0.479 0.844,0.479 0.979,0.479 false 0.542,1.156 0.354,0.844 0.354,0.844 0.24,0.844 false 0.813,1.531 0.844,1.885 0.844,1.885 0.958,1.885 false 1.802,0.76 1.958,0.958 0.156,0.198 10 false 3 3.125,0.76 3.281,0.958 0.156,0.198 10 false 5 3.135,1.406 3.292,1.604 0.156,0.198 10 false 1 1.813,1.406 1.969,1.604 0.156,0.198 10 false 2 1.01,1.792 1.167,1.99 0.156,0.198 10 false 3 0.115,0.75 0.271,0.948 0.156,0.198 10 false 1 1.021,0.396 1.177,0.594 0.156,0.198 10 false 5 1.5,0.74 1.656,0.938 0.156,0.198 10 false 2 0.167,0.167 0.323,0.365 0.156,0.198 10 false *a
*a Component without harness connected
(PTC Heater Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - POWER SOURCE)

NG

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC HTR NO. 1:
Tester Connection Condition Specified Condition
5 (PTC HTR NO. 1 Relay) - Body ground Always 11 to 14 V
1 (PTC HTR NO. 1 Relay) - Body ground Ignition switch off Below 1 V
1 (PTC HTR NO. 1 Relay) - Body ground Ignition switch ON 11 to 14 V


Standard Voltage:
PTC HTR NO. 2:
Tester Connection Condition Specified Condition
5 (PTC HTR NO. 2 Relay) - Body ground Always 11 to 14 V
1 (PTC HTR NO. 2 Relay) - Body ground Ignition switch off Below 1 V
1 (PTC HTR NO. 2 Relay) - Body ground Ignition switch ON 11 to 14 V


Standard Voltage:
PTC HTR NO. 3:
Tester Connection Condition Specified Condition
5 (PTC HTR NO. 3 Relay) - Body ground Always 11 to 14 V
1 (PTC HTR NO. 3 Relay) - Body ground Ignition switch off Below 1 V
1 (PTC HTR NO. 3 Relay) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO. 1:
Tester Connection Condition Specified Condition
2 (PTC HTR NO. 1 Relay) - F80-40 (PTC1) Always Below 1 Ω
2 (PTC HTR NO. 1 Relay) or F80-40 (PTC1) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 2:
Tester Connection Condition Specified Condition
2 (PTC HTR NO. 2 Relay) - F80-3 (PTC2) Always Below 1 Ω
2 (PTC HTR NO. 2 Relay) or F80-3 (PTC2) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 3:
Tester Connection Condition Specified Condition
2 (PTC HTR NO. 3 Relay) - F80-36 (PTC3) Always Below 1 Ω
2 (PTC HTR NO. 3 Relay) or F80-36 (PTC3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER ASSEMBLY)
a.

Disconnect the F36 quick heater assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC HTR NO. 1:
Tester Connection Condition Specified Condition
3 (PTC HTR NO. 1 Relay) - F36-2 (B) Always Below 1 Ω
3 (PTC HTR NO. 1 Relay) or F36-2 (B) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 2:
Tester Connection Condition Specified Condition
3 (PTC HTR NO. 2 Relay) - F36-3 (B) Always Below 1 Ω
3 (PTC HTR NO. 2 Relay) or F36-3 (B) - Body ground Always 10 kΩ or higher


Standard Resistance:
PTC HTR NO. 3:
Tester Connection Condition Specified Condition
3 (PTC HTR NO. 3 Relay) - F36-1 (B) Always Below 1 Ω
3 (PTC HTR NO. 3 Relay) or F36-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - BODY GROUND)
a.

Disconnect the F37 quick heater assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F37-1 (E) - Body ground Always Below 1 Ω
F37-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT QUICK HEATER ASSEMBLY
a.

b.
E170870C14
1.531,0.417 2,0.656 0.469,0.24 1.51,2.76 1.979,3 0.469,0.24 1.094,1.885 1.51,1.469 false 2.458,1.906 2.021,1.438 false 1.792,1.99 1.781,1.469 false 1.156,4.219 1.573,3.802 false 2.333,4.208 1.917,3.781 false 0.396,0.521 0.781,0.906 0.385,0.385 10 false *a 1.656,0.458 2.042,0.75 0.385,0.292 10 false F36 1.625,2.802 2.01,3.094 0.385,0.292 10 false F37 1.031,1.906 1.417,2.292 0.385,0.385 10 false B 1.76,2.021 2.146,2.406 0.385,0.385 10 false B 2.469,1.938 2.854,2.323 0.385,0.385 10 false B 1.083,4.24 1.469,4.625 0.385,0.385 10 false E 2.365,4.24 2.75,4.625 0.385,0.385 10 false E
*a Component without harness connected
(Quick Heater Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F36-1 (B) - F37-1 (E) Always Below 1 Ω
F36-2 (B) - F37-2 (E) Always Below 1 Ω
F36-3 (B) - F37-1 (E) Always Below 1 Ω
F36-3 (B) - F37-2 (E) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG