Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019671 1AR-FE ENGINE CONTROL _0103543 SFI SYSTEM U

1AR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A247842E63
2.406,0.406 2.802,0.646 0.396,0.24 5.906,0.406 6.302,0.646 0.396,0.24 2.521,0.438 2.823,0.594 0.302,0.156 10 false C1 5.979,0.438 6.281,0.594 0.302,0.156 10 false A43

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A43-1 (BATT) - C1-16 (E1) GR - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
C1-29 (+BM) - C1-16 (E1) R - BR Power source of throttle actuator Always 11 to 14 V
A43-37 (IGSW) - C1-16 (E1) W - BR Ignition switch signal Ignition switch ON 11 to 14 V
A43-2 (+B) - C1-16 (E1) G - BR Power source of ECM Ignition switch ON 11 to 14 V
A43-3 (+B2) - C1-16 (E1) R - BR Power source of ECM Ignition switch ON 11 to 14 V
C1-74 (OC1+) - C1-75 (OC1-) W - B Camshaft timing oil control valve assembly (for intake camshaft) operation signal Idling Pulse generation
(See waveform 1)
C1-65 (OE1+) - C1-64 (OE1-) R - GR Camshaft timing oil control valve assembly (for exhaust camshaft) operation signal Idling Pulse generation
(See waveform 2)
A43-46 (MREL) - C1-16 (E1) B - BR EFI MAIN relay operation signal Ignition switch ON 11 to 14 V
C1-91 (VG) - C1-92 (E2G) L - R Mass air flow meter sub-assembly signal Idling, shift lever in P or N, A/C switch off 0.5 to 3.0 V
C1-93 (THA) - C1-94 (ETHA) P - Y Intake air temperature sensor signal Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
C1-95 (THW) - C1-96 (ETHW) B - P Engine coolant temperature sensor signal Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C1-125 (VCTA) - C1-126 (ETA) B - R Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-127 (VTA1) - C1-126 (ETA) Y - R Throttle position sensor signal (for engine control) Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
3.2 to 4.8 V
C1-128 (VTA2) - C1-126 (ETA) BR - R Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON,
accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON,
accelerator pedal fully depressed
4.6 to 5.0 V
A43-51 (VPA) - A43-52 (EPA) G - Y Accelerator pedal position sensor signal (for engine control) Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
A43-54 (VPA2) - A43-55 (EPA2) R - BE Accelerator pedal position sensor signal Ignition switch ON,
accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 4.75 V
A43-53 (VCPA) - A43-52 (EPA) B - Y Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A43-56 (VCP2) - A43-55 (EPA2) W - BE Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C1-23 (HA1A) - C1-53 (E04) R - W-B Air fuel ratio sensor heater operation signal Idling Pulse generation
(See waveform 3)
Ignition switch ON 11 to 14 V
C1-133 (A1A+) - C1-16 (E1) L - BR Air fuel ratio sensor signal Ignition switch ON 3.3 V*1
C1-134 (A1A-) - C1-16 (E1) P - BR Air fuel ratio sensor signal Ignition switch ON 2.9 V*1
C1-24 (HT1B) - C1-53 (E04) G - W-B Heated oxygen sensor heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C1-100 (OX1B) - C1-132 (EX1B) W - GR Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 4)
C1-20 (#10) - C1-50 (E01) B - W-B No. 1 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 5)
C1-17 (#20) - C1-50 (E01) R - W-B No. 2 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 5)
C1-18 (#30) - C1-50 (E01) Y - W-B No. 3 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 5)
C1-19 (#40) - C1-50 (E01) L - W-B No. 4 fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 5)
C1-123 (KNK1) - C1-124 (EKNK) R - G Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 6)
C1-82 (VV1+) - C1-114 (VV1-) V - L Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 7)
C1-81 (EV1+) - C1-112 (EV1-) W - LG Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 7)
C1-76 (NE+) - C1-109 (NE-) B - W Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 8)
C1-57 (IGT1) - C1-16 (E1) Y - BR No. 1 ignition coil assembly signal (ignition signal) Idling Pulse generation
(See waveform 9)
C1-56 (IGT2) - C1-16 (E1) R - BR No. 2 ignition coil assembly signal (ignition signal) Idling Pulse generation
(See waveform 9)
C1-55 (IGT3) - C1-16 (E1) G - BR No. 3 ignition coil assembly signal (ignition signal) Idling Pulse generation
(See waveform 9)
C1-54 (IGT4) - C1-16 (E1) L - BR No. 4 ignition coil assembly signal (ignition signal) Idling Pulse generation
(See waveform 9)
C1-51 (IGF1) - C1-16 (E1) W - BR Ignition coil assembly (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(See waveform 9)
C1-68 (PRG) - C1-50 (E01) R - W-B Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See waveform 10)
A43-57 (SPD) - C1-16 (E1) BE - BR Vehicle speed signal from combination meter assembly signal Driving at 20 km/h (12 mph) Pulse generation
(See waveform 11)
A43-22 (STA) - C1-16 (E1) P - BR Starter assembly signal Cranking 6.0 V or higher
C1-63 (NSW) - C1-16 (E1) LG - BR Park/Neutral position switch assembly signal Ignition switch ON, shift lever in P or N Below 2.0 V
Ignition switch ON, shift lever not in P or N 11 to 14 V
A43-11 (STP) - C1-16 (E1) G - BR Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A43-24 (ST1-) - C1-16 (E1) L - BR Stop light switch assembly signal
(opposite of voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
C1-60 (M+) - C1-58 (ME01) W - BR Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 12)
C1-30 (M-) - C1-58 (ME01) B - BR Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(See waveform 13)
A43-21 (FC) - C1-50 (E01) L - W-B Fuel pump control Ignition switch ON 11 to 14 V
Idling Below 1.5 V
A43-23 (TC) - C1-16 (E1) G - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A43-31 (TACH) - C1-16 (E1) L - BR Engine speed signal Idling Pulse generation
(See waveform 14)
C1-113 (VCV1) - C1-16 (E1) B - BR Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-111 (VCE1) - C1-16 (E1) P - BR Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
C1-73 (ALT) - C1-16 (E1) L - BR Generator assembly Ignition switch ON 11 to 14 V
A43-13 (CANH) - C1-16 (E1) B - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 15)
A43-26 (CANL) - C1-16 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(See waveform 16)
C1-69 (ACIS) - C1-50 (E01) L - W-B Vacuum switching valve assembly (for acoustic control induction system) operation signal Ignition switch ON 11 to 14 V
C1-22 (IA1+) - C1-50 (E01) G - W-B Intake air control valve actuator (for tumble control valve) Idling with cold engine Pulse generation
(See waveform 17)
C1-21 (IA1-) - C1-50 (E01) LG - W-B Intake air control valve actuator (for tumble control valve) Idling with cold engine Pulse generation
(See waveform 18)
C1-131 (IAC1) - C1-129 (EIA1) R - L Tumble control valve position sensor Ignition switch off to ON 3.0 to 4.0 V
C1-130 (VCIA) - C1-16 (E1) B - BR Power source of tumble control valve position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
A43-44 (RFC) - C1-16 (E1) W - BR Cooling fan control Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 19)
A43-18 (SNWI) - C1-16 (E1) GR - BR SNOW mode switch signal Ignition switch ON 11 to 14 V
Ignition switch ON, SNOW mode switch being pushed and held Below 1.5 V
A43-45 (NEO)*2 - C1-16 (E1) GR - W-B Engine speed signal sent to certification ECU (smart key ECU assembly) Idling with warm engine Pulse generation
(See waveform 20)
A43-14 (EC) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C1-50 (E01) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C1-49 (E02) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
C1-58 (ME01) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
C1-59 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

*2: w/ Smart Entry and Start System.

WAVEFORM 1


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 2


A292381E01
0.615,1.125 1.073,1.323 0.458,0.198 10 GND 0.594,0.198 1.563,0.448 0.969,0.25 10 5 V/DIV. 1.906,1.854 2.625,2.073 0.719,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Operation Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 3


A205412E06
2.646,0.042 3.25,0.229 0.604,0.188 10 5 V/DIV. 2.698,0.906 3.063,1.073 0.365,0.167 10 GND 1.156,1.865 1.917,2.042 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling


WAVEFORM 4


A292382E01
0.615,1.469 1.073,1.667 0.458,0.198 10 GND 0.479,0.177 1.469,0.365 0.99,0.188 10 0.2 V/DIV. 1.854,1.906 2.844,2.094 0.99,0.188 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, the item O2S B1S2 shows the values input to the ECM from the heated oxygen sensor.



WAVEFORM 5


A292383E01
0.667,1.583 1.125,1.781 0.458,0.198 10 GND 1.865,1.906 2.75,2.104 0.885,0.198 10 20 ms./DIV. 0.531,0.177 1.417,0.375 0.885,0.198 10 20 V/DIV.

No. 1 (to No. 4) Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 6


A283572E06
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




WAVEFORM 7


A255508E16
0.104,0.042 0.708,0.198 0.604,0.156 10 5 V/DIV. 0.104,0.646 0.427,0.813 0.323,0.167 10 CH1 0.125,1.469 0.448,1.635 0.323,0.167 10 CH2 0.052,0.813 0.427,1.01 0.375,0.198 10 (VV1) 0.063,1.625 0.458,1.813 0.396,0.188 10 (EV1) 3.042,0.823 3.365,1.021 0.323,0.198 10 GND 3.031,1.594 3.375,1.854 0.344,0.26 10 GND 1.302,1.896 2.052,2.073 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 8


A254145E02
2.984,0.964 3.337,1.167 0.353,0.202 10 GND 0.067,0.058 0.612,0.235 0.545,0.177 10 5 V/DIV. 1.22,1.917 1.972,2.062 0.751,0.145 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 9


A122717E41
3.021,0.917 3.385,1.115 0.365,0.198 10 false GND 3.021,1.563 3.354,1.76 0.333,0.198 10 false GND 0.208,0.302 0.521,0.708 0.313,0.406 10 false CH1 (IGT) 0.198,1.333 0.573,1.5 0.375,0.167 10 false CH2 0.021,0.01 0.563,0.188 0.542,0.177 10 false 2 V/DIV. 1.292,1.906 2.042,2.052 0.75,0.146 10 false 20 ms./DIV. 0.198,1.5 0.594,1.74 0.396,0.24 10 false (IGF1)

Ignition Coil Assembly Signal (IGT and IGF1 Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 10


A218020E09
2.667,0.177 3.365,0.448 0.698,0.271 10 10 V/DIV. 2.802,0.948 3.26,1.292 0.458,0.344 10 GND 1.188,1.792 2,2 0.813,0.208 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A292384E01
2.813,1.25 3.271,1.448 0.458,0.198 10 GND 1.146,2.01 1.917,2.167 0.771,0.156 10 20 ms./DIV. 2.708,0.135 3.313,0.313 0.604,0.177 10 5 V/DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 12


A208000E03
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 13


A245848E01
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 14


A292385E01
0.542,1.167 1,1.365 0.458,0.198 10 GND 0.125,0.125 0.948,0.354 0.823,0.229 10 5 V/DIV. 1.75,1.917 2.563,2.104 0.813,0.188 10 10 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A292386E01
1.365,1.917 2.104,2.094 0.74,0.177 10 10 μs./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 16


A292387E02
3,1.375 3.344,1.573 0.344,0.198 10 GND 2.781,0.26 3.385,0.469 0.604,0.208 10 1 V/DIV. 1.385,1.885 2.156,2.052 0.771,0.167 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 17


A292388E01
0.667,1.333 1.125,1.531 0.458,0.198 10 GND 0.635,0.156 1.25,0.365 0.615,0.208 10 5 V/DIV. 1.875,1.854 2.563,2.073 0.688,0.219 10 1 ms./DIV.

Positive Terminal of Intake Air Control Valve Actuator (for Tumble Control Valve) Signal
ECM Terminal Name Between IA1+ and E01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with cold engine


WAVEFORM 18


A292389E01
0.667,1.333 1.125,1.531 0.458,0.198 10 GND 0.646,0.188 1.219,0.385 0.573,0.198 10 5 V/DIV. 1.833,1.844 2.531,2.042 0.698,0.198 10 1 ms./DIV.

Negative Terminal of Intake Air Control Valve Actuator (for Tumble Control Valve) Signal
ECM Terminal Name Between IA1- and E01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with cold engine


WAVEFORM 19


A282867E05
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 20


A210050E04
2.833,2.385 3.167,2.542 0.333,0.156 10 GND 1.125,2.75 1.792,3.021 0.667,0.271 10 2 ms./DIV. 2.229,0.563 2.771,0.854 0.542,0.292 10 5 V/DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.