Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2017.10
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303922 AUTOMATIC TRANSAXLE SYSTEM C

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P275612  Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery  


DESCRIPTION

The ECM controls the solenoid (SLU) valve using a predetermined current, and performs lock-up and flex lock-up control.

C361130C02
4.833,1.667 4.083,0.75 4.083,0.75 3.917,0.75 true 5,1.917 4.5,2.5 4.5,2.5 4.333,2.5 true 6.083,1.417 5.417,2.833 5.417,2.833 6.083,2 true 1.917,2.813 2.99,3.01 1.073,0.198 10 false *a 0.708,2.104 1.302,2.521 0.594,0.417 10 false *b 5.323,2.865 5.917,3.156 0.594,0.292 10 false *3 4.146,2.427 5.063,2.625 0.917,0.198 10 false *2 3.729,0.667 5.417,0.865 1.688,0.198 10 false *1
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Current *b Hydraulic Pressure


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P275612 Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Battery 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Vehicle is being driven

2.

Solenoid (SLU) valve circuit is short to +B

3.

1 second

4.

1-trip detection logic


·

Solenoid (SLU) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P2763

MONITOR DESCRIPTION

When a short to +B in the solenoid (SLU) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

WIRING DIAGRAM

C388294E19
1.104,1.573 4.167,1.771 3.063,0.198 10 false Solenoid (SLU) Valve 0.729,1.208 0.979,1.448 0.25,0.24 10 false 1 0.729,1.958 0.979,2.198 0.25,0.24 10 false 2 2.448,0.844 2.938,1.063 0.49,0.219 10 false SLU+ 2.448,2.083 2.938,2.302 0.49,0.219 10 false SLU- 5.26,2.083 5.75,2.302 0.49,0.219 10 false SLU- 5.26,0.844 5.75,1.063 0.49,0.219 10 false SLU+ 2.906,0.844 3.396,1.063 0.49,0.219 10 false 5 2.906,2.073 3.396,2.292 0.49,0.219 10 false 4 4.948,0.844 5.438,1.063 0.49,0.219 10 false 76 4.979,2.083 5.469,2.302 0.49,0.219 10 false 61 6,0.594 6.49,0.813 0.49,0.219 10 false 12 V 1.115,2.844 1.604,3.063 0.49,0.219 10 false C85 1.115,3.021 4.177,3.219 3.063,0.198 10 false Transmission Wire 5.729,2.865 6.219,3.083 0.49,0.219 10 false C1 5.729,3.042 6.219,3.26 0.49,0.219 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After the performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLU) VALVE) - ECM)
a.

Disconnect the C1 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-76 (SLU+) or C1-61 (SLU-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C85 transmission wire connector.


b.

Disconnect the C1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-5 (SLU+) or C1-76 (SLU+) - Other terminals Always 10 kΩ or higher
C85-4 (SLU-) or C1-61 (SLU-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SLU) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.INSPECT SOLENOID (SLU) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLU) Valve)


Remove the solenoid (SLU) valve.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLU) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes operating sound.



Result:
Proceed to
OK
NG



OK

NG