Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2018.09
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0107365 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41311F 1.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C201521N05
2.458,0.592 2.768,0.735 0.31,0.143 10 SST 1.87,0.803 2.406,0.689 2.406,0.689 1.887,1.007 false 1.747,0.661 2.406,0.689 false

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing (inner race) cage when installing the front differential case rear tapered roller bearing (inner race).

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing (inner race) and front differential case.




b.
C196828N04
0.885,1.125 0.573,1.396 0.573,1.396 0.74,1.396 false 2.635,1.104 2.563,0.802 2.563,0.802 2.667,0.802 false 0.219,1.323 0.531,1.479 0.313,0.156 10 true SST 2.24,0.719 2.552,0.875 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing (outer race) and transaxle case sub-assembly.



Hide 41311E 2.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C297473N02
0.833,0.823 0.406,0.458 0.406,0.458 0.927,0.51 false 0.427,0.469 0.865,0.698 false 2.365,0.604 2.292,0.281 2.292,0.281 2.552,0.323 false 2.302,0.292 2.479,0.51 false 0.104,0.375 0.563,0.573 0.458,0.198 10 false SST 1.99,0.198 2.448,0.396 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case.

SST
09523-36010  
09950-60010  (09951-00540)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing (inner race) cage when installing the front differential case front tapered roller bearing (inner race).

·

Ensure that there is no clearance between the front differential case front tapered roller bearing (inner race) and front differential case.




b.
C196830N04
0.938,1.24 0.625,1.594 0.625,1.594 0.896,1.531 false 2.604,0.698 2.5,0.698 2.5,0.698 2.552,1.073 false 0.281,1.542 0.594,1.708 0.313,0.167 10 false SST 2.188,0.635 2.49,0.802 0.302,0.167 10 false SST

Install the shim to the transaxle housing.


c.

Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case front tapered roller bearing (outer race), shim and transaxle housing.



Hide 41039A 3.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C02
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

ATF


Coat the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs with ATF.


b.
C309130C01
2.229,0.177 2.427,0.177 false 2.229,0.333 2.448,0.333 false 2.219,0.74 2.344,0.74 false 2.219,1.292 2.344,1.292 false 2.229,1.708 2.469,1.708 false 2.229,1.865 2.427,1.865 false 2.01,1.208 2.323,1.365 0.313,0.156 10 false *1 2.031,1.625 2.344,1.781 0.313,0.156 10 false *2 2.031,1.792 2.344,1.948 0.313,0.156 10 false *3 2.021,0.667 2.333,0.823 0.313,0.156 10 false *1 2.031,0.26 2.344,0.417 0.313,0.156 10 false *2 2.021,0.094 2.333,0.25 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.

·

Make sure that the conical spring is installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C312291C01
4.656,0.24 5.125,0.24 false 4.927,1.531 5.115,1.667 false 4.396,1.531 4.927,1.531 4.927,1.531 5.115,1.396 false 3.167,0.219 3.479,0.375 0.313,0.156 10 false *a 1.104,2.396 1.417,2.552 0.313,0.156 10 false *b 4.344,0.156 4.656,0.313 0.313,0.156 10 false SST 4.104,1.438 4.417,1.594 0.313,0.156 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C287727C02
0,0 0,0 false
V100135

ATF


Coat the 2 front differential pinions and 2 front differential pinion thrust washers with ATF.


e.
C309133C01
2.656,2.75 2.49,2.75 2.49,2.75 2.49,2.281 true 1.938,0.75 2.25,0.906 0.313,0.156 10 false *a 2.74,2.677 3.125,2.865 0.385,0.188 10 false SST
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 4.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 5.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C309134C01
0,0 0,0 false
V100135

ATF


Coat the front No. 1 differential pinion shaft with ATF.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41342A 7.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C309135

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C309136

Using a chisel and a hammer, stake the front differential case.


Hide 8.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C205239

Install the front differential case to the transaxle case sub-assembly.


c.
C136447N05
1.51,1.615 2.49,1.958 2.49,1.958 2.208,1.646 false 1.906,1.646 2.49,1.958 false 2.573,0.938 3.052,1.104 3.052,1.104 2.49,1.417 false 3.063,1.104 2.604,1.146 false 2,0.615 2.896,0.188 2.896,0.188 2.271,0.76 false 1.781,0.531 2.875,0.198 false 1.344,0.469 0.552,0.271 0.552,0.271 0.875,0.74 false 1.156,0.531 0.552,0.271 0.552,0.271 1.021,0.635 false 0.594,1.021 0.229,1.354 0.229,1.354 0.677,1.604 false 0.573,1.396 0.229,1.354 0.229,1.354 0.542,1.198 false 0.875,1.76 1.188,1.979 1.188,1.979 1.313,1.729 false 1.188,1.969 1.115,1.802 false 2.917,0.094 3.052,0.25 0.135,0.156 10 false A 2.5,1.865 2.635,2.021 0.135,0.156 10 false B 0.385,0.156 0.521,0.313 0.135,0.156 10 false A 3.083,1.031 3.219,1.188 0.135,0.156 10 false A 1.177,1.99 1.313,2.146 0.135,0.156 10 false A 0.083,1.271 0.219,1.427 0.135,0.156 10 false A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)
Bolt (B) : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)


d.
C138262N16
0.841,4.027 1.205,4.212 0.364,0.184 10 SST 1.079,3.308 0.973,4.027 false

Using SST, turn the front differential case right and left 2 or 3 times to settle the bearings.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the differential side bearings while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

1.5 to 1.7 N*m (16 to 17 kgf*cm, 14 to 15 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness: mm (in.):
No. Thickness No. Thickness
90564-69001 2.000 (0.0787) 90564-69021 2.450 (0.0965)
90564-69002 2.025 (0.0797) 90564-69022 2.475 (0.0974)
90564-69003 2.050 (0.0807) 90564-69023 2.500 (0.0984)
90564-69004 2.075 (0.0817) 90564-69024 2.525 (0.0994)
90564-69005 2.100 (0.0827) 90564-69025 2.550 (0.100)
90564-69006 2.125 (0.0837) 90564-69026 2.575 (0.101)
90564-69007 2.150 (0.0846) 90564-69027 2.600 (0.102)
90564-69008 2.175 (0.0856) 90564-69028 2.625 (0.103)
90564-69009 2.200 (0.0866) 90564-69029 2.650 (0.104)
90564-69010 2.225 (0.0876) 90564-69030 2.675 (0.105)
90564-69011 2.250 (0.0886) 90564-69031 2.700 (0.106)
90564-69012 2.275 (0.0896) 90564-69032 2.725 (0.107)
90564-69013 2.300 (0.0906) 90564-69033 2.750 (0.108)
90564-69014 2.325 (0.0915) 90564-69034 2.775 (0.109)
90564-69015 2.350 (0.0925) 90564-69035 2.800 (0.110)
90564-69016 2.375 (0.0935) 90564-69036 2.825 (0.111)
90564-69017 2.400 (0.0945) 90564-69037 2.850 (0.112)
90564-69020 2.425 (0.0955) 90564-69038 2.875 (0.113)



f.
C287968

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.
C205239

Remove the front differential case from the transaxle case sub-assembly.


Hide 41221 9.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.
C306369C02
1.188,1.521 0.604,0.927 0.604,0.927 1.26,1.438 false 0.427,0.792 0.74,0.99 0.313,0.198 10 false *a
*a Matchmark


Clean the contact surface of the front differential case.


c.

Align the matchmarks, and install the front differential ring gear to the front differential case quickly.


d.
C138532

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 43420H 10.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C307374N01
1.396,1.542 0.781,2.354 0.781,2.354 1.427,1.302 false 2.365,1.875 2.667,1.76 2.667,1.76 1.781,1.76 false 0.458,2.292 0.917,2.49 0.458,0.198 10 false SST 2.719,1.708 3.177,1.906 0.458,0.198 10 false SST

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.

Using SST and a hammer, install the front drive shaft oil seal LH.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43410M 11.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C307375N01
0.604,0.427 0.781,0.427 0.781,0.427 0.969,0.802 false 2.208,1.948 2.438,1.948 false 0.302,0.365 0.76,0.563 0.458,0.198 10 false SST 1.896,1.875 2.354,2.073 0.458,0.198 10 false SST

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.

Using SST and a hammer, install the front drive shaft oil seal RH.

SST
09316-60011  (09316-00011)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal RH.