Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE(When Not Using the Engine Support Bridge) › from 2018.09
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0303752 TRANSMISSION WIRE(When Not Using the Engine Support Bridge) A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE(When Not Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 82125J 1.INSTALL TRANSMISSION WIRE

a.
C362373

Coat the O-ring of the transmission wire with Toyota Genuine ATF WS.


b.

Install the transmission wire to the automatic transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


d.

Install the temperature sensor to the transmission valve body assembly with the bolt and temperature sensor clamp.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)

NOTICE:
C362643C02
1.688,1.646 1.99,1.833 true 1.083,1.167 1.5,1.333 true 1.969,1.865 2.198,2.031 0.229,0.167 10 true *a 0.823,1.063 1.052,1.219 0.229,0.156 10 true *b
*a Transmission Wire (Temperature Sensor Wire)
*b Transmission Revolution Sensor (NC) Wire


To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, pass the transmission revolution sensor (NC) wire under the transmission wire (temperature sensor wire) as shown in the illustration.



e.
C365930

Connect the 9 solenoid valve connectors.

NOTICE:
C362374C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area.


·

To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission wire ride up over the area shown in the illustration.

·

To prevent it from being pinched between the transmission case side cover and the automatic transaxle case sub-assembly, do not let the transmission wire protrude toward the transmission case side cover installation surface.




f.
C365931

Engage the clamp to connect the transmission wire to the solenoid lock plate.


Hide 35151F 2.INSTALL TRANSMISSION CASE SIDE COVER (for TMC, TMMWV Made)

HINT:
·
C362609C02
1.521,0.458 1.885,0.198 true 1,1.49 1.385,1.979 true 1.448,1.938 1.667,2.146 0.219,0.208 10 true *a 1.938,0.094 2.177,0.302 0.24,0.208 10 true *b
*a TMC Made
*b AW, TMMWV Made


The component manufacturer (TMC (TOYOTA), TMMWV (TOYOTA) or AW (AISIN AW)) can be determined based on the location of the serial number.

·

for AW, TMMWV Made:

The component manufacturer (TMMWV (TOYOTA) or AW (AISIN AW)) can be determined based on the serial number as described in the following table.

Serial Number Factory
##6######## AW (AISIN AW)
##A######## TMMWV



a.
C362642C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.



b.
C378385

Clean the 3 bolt holes shown in the illustration.


c.
P000601C53
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt (A) and 2 bolts (D).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolts immediately after applying adhesive to prevent foreign matter from attaching to them.


HINT:

The bolt (A) and 2 bolts (D) are in the locations shown in the following step.



d.
C401609C01
0.063,0.052 0.385,0.302 0.323,0.25 12 false *A 0.063,2.333 0.375,2.563 0.313,0.229 12 false *B 1.208,2.115 1.365,2.313 0.156,0.198 10 false A 0.938,1.281 1.094,1.479 0.156,0.198 10 true D 0.938,0.792 1.094,0.99 0.156,0.198 10 true D 1.219,0.146 1.375,0.344 0.156,0.198 10 false C 1.865,0.135 2.021,0.333 0.156,0.198 10 false C 2.688,0.26 2.844,0.458 0.156,0.198 10 false B 2.771,1.104 2.927,1.302 0.156,0.198 10 false C 2.708,1.594 2.865,1.792 0.156,0.198 10 false C 2.406,2.063 2.563,2.26 0.156,0.198 10 false C 1.771,2.188 1.927,2.385 0.156,0.198 10 false C 1.875,2.354 2.031,2.552 0.156,0.198 10 false C 1.219,2.375 1.375,2.573 0.156,0.198 10 false C 2.771,3.323 2.938,3.51 0.167,0.188 10 false C 2.719,3.813 2.875,4.01 0.156,0.198 10 false C 2.698,2.49 2.854,2.688 0.156,0.198 10 false B 1.229,4.333 1.385,4.531 0.156,0.198 10 false A 2.406,4.281 2.563,4.479 0.156,0.198 10 false C 1.792,4.396 1.948,4.594 0.156,0.198 10 false C 0.948,3.49 1.104,3.688 0.156,0.198 10 true D 0.958,3.021 1.115,3.219 0.156,0.198 10 true D
*A for TMC Made
*B for TMMWV Made


Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts ((A) and (B)).

NOTICE:
·

Bolt (A) is an adhesive-coated bolt.

·

To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.




e.

Temporarily install the 6 bolts (C) and 2 bolts (D).

NOTICE:

Bolt (D) is an adhesive-coated bolt.



f.
C401609C03
0.063,0.052 0.385,0.302 0.323,0.25 12 false *A 0.063,2.333 0.375,2.563 0.313,0.229 12 false *B 1.208,2.115 1.365,2.313 0.156,0.198 10 false 1 0.938,1.281 1.094,1.479 0.156,0.198 10 true 9 0.938,0.792 1.094,0.99 0.156,0.198 10 true 5 1.219,0.146 1.375,0.344 0.156,0.198 10 false 3 1.875,0.135 2.031,0.333 0.156,0.198 10 false 7 2.688,0.26 2.844,0.458 0.156,0.198 10 false 2 2.771,1.104 2.927,1.302 0.156,0.198 10 false 6 2.708,1.594 2.979,1.833 0.271,0.24 10 false 10 2.406,2.063 2.563,2.26 0.156,0.198 10 false 4 1.781,2.188 1.938,2.385 0.156,0.198 10 false 8 1.875,2.354 2.031,2.552 0.156,0.198 10 false 7 1.219,2.375 1.375,2.573 0.156,0.198 10 false 3 2.771,3.323 2.938,3.51 0.167,0.188 10 false 6 2.719,3.813 2.917,4.063 0.198,0.25 10 false 10 2.698,2.49 2.854,2.688 0.156,0.198 10 false 2 1.229,4.333 1.385,4.531 0.156,0.198 10 false 1 2.406,4.281 2.563,4.479 0.156,0.198 10 false 4 1.792,4.396 1.948,4.594 0.156,0.198 10 false 8 0.948,3.49 1.104,3.688 0.156,0.198 10 true 9 0.958,3.021 1.115,3.219 0.156,0.198 10 true 5
*A for TMC Made
*B for TMMWV Made


Fully tighten the 10 bolts in the order shown in the illustration.

Torque:
Bolt (A) and Bolt (D) : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
Bolt (B) and Bolt (C) : 7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 35151F 3.INSTALL TRANSMISSION CASE SIDE COVER (for AISIN AW Made)

HINT:
·
C362609C02
1.521,0.458 1.885,0.198 true 1,1.49 1.385,1.979 true 1.448,1.938 1.667,2.146 0.219,0.208 10 true *a 1.938,0.094 2.177,0.302 0.24,0.208 10 true *b
*a TMC Made
*b AW, TMMWV Made


The component manufacturer (TMC (TOYOTA), TMMWV (TOYOTA) or AW (AISIN AW)) can be determined based on the location of the serial number.

·

for AW, TMMWV Made:

The component manufacturer (TMMWV (TOYOTA) or AW (AISIN AW)) can be determined based on the serial number as described in the following table.

Serial Number Factory
##6######## AW (AISIN AW)
##A######## TMMWV



a.
C362642C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.



b.
C365942N01
1.094,1.979 1.292,2.177 0.198,0.198 10 false A 1.635,1.979 1.833,2.177 0.198,0.198 10 false C 2.177,1.979 2.375,2.177 0.198,0.198 10 false C 2.844,1.521 3.042,1.719 0.198,0.198 10 false C 2.885,0.938 3.083,1.135 0.198,0.198 10 false C 2.771,0 2.969,0.198 0.198,0.198 10 false B 2.031,0.01 2.229,0.208 0.198,0.198 10 false C 1.365,0 1.563,0.198 0.198,0.198 10 false C 0.896,0.625 1.052,0.823 0.156,0.198 10 true C 0.896,1.156 1.052,1.354 0.156,0.198 10 true C

Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts (A and B).

NOTICE:

To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.



c.

Temporarily install the 8 bolts (C).


d.
C365942N05
1.073,1.958 1.469,2.167 0.396,0.208 10 false 1 1.635,1.979 1.833,2.177 0.198,0.198 10 false 8 2.531,1.938 2.729,2.135 0.198,0.198 10 false 4 2.844,1.521 3.115,1.74 0.271,0.219 10 false 10 2.885,0.938 3.083,1.135 0.198,0.198 10 false 6 2.771,0 2.969,0.198 0.198,0.198 10 false 2 2.031,0.01 2.229,0.208 0.198,0.198 10 false 7 1.365,0 1.563,0.198 0.198,0.198 10 false 3 0.896,0.625 1.052,0.823 0.156,0.198 10 true 5 0.896,1.156 1.052,1.354 0.156,0.198 10 true 9

Fully tighten the 10 bolts in the order shown in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 32901C 4.INSTALL OIL COOLER UNION SUB-ASSEMBLY

a.
C362358C01
1.49,2.802 1.656,2.719 false 2.146,2.823 1.635,3.031 1.635,3.031 1.844,2.833 true 1.281,2.74 1.594,2.896 0.313,0.156 10 false *1 1.438,2.979 1.75,3.135 0.313,0.156 10 false *2
*1 Oil Cooler Union Bolt
*2 Gasket


Pass the oil cooler union sub-assembly through 2 new gaskets and temporarily install it to the automatic transaxle case sub-assembly.


b.

Temporarily install the oil cooler union sub-assembly bracket portion to the automatic transaxle case sub-assembly with the bolt.


c.

Fully tighten the oil cooler union bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)


d.

Fully tighten the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)