RM3160E
_V1
General
_019682
SPECIFICATIONS
_0095363
1AR-FE ENGINE MECHANICAL
F
SPECIFICATIONS 1AR-FE ENGINE MECHANICAL TORQUE SPECIFICATIONS
CAMSHAFT
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
in.*lbf
|
| Camshaft bearing cap x Camshaft housing sub-assembly
|
16
|
163
|
12
|
|
| Camshaft housing sub-assembly x Cylinder head sub-assembly
|
27
|
275
|
20
|
|
| Camshaft timing gear assembly x Camshaft
|
85
|
867
|
63
|
|
| Camshaft timing exhaust gear assembly x No. 2 camshaft
|
85
|
867
|
63
|
|
| No. 1 chain tensioner assembly x Cylinder block sub-assembly
|
10
|
102
|
7
|
|
| Timing chain cover plate x Timing chain cover sub-assembly
|
10
|
102
|
7
|
|
| Engine wire x Engine
|
Nut (A)
|
9.8
|
100
|
|
87
|
| Nut (B)
|
12
|
122
|
9
|
|
| Bolt (C)
|
8.0
|
82
|
|
71
|
| Bolt (D)
|
8.5
|
87
|
|
75
|
CYLINDER HEAD GASKET
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
| Cylinder head sub-assembly x Cylinder block sub-assembly
|
1st
|
36
|
367
|
27
|
| 2nd
|
36
|
367
|
27
|
| 3rd
|
Turn 90°
|
| 4th
|
Turn 90°
|
| Camshaft bearing cap x Camshaft housing sub-assembly
|
16
|
163
|
12
|
| Camshaft housing sub-assembly x Cylinder head sub-assembly
|
27
|
275
|
20
|
| Camshaft timing gear assembly x Camshaft
|
85
|
867
|
63
|
| Camshaft timing exhaust gear assembly x No. 2 camshaft
|
85
|
867
|
63
|
| No. 1 chain vibration damper x Cylinder block sub-assembly
|
21
|
214
|
15
|
| Chain tensioner slipper x Cylinder head sub-assembly
|
21
|
214
|
15
|
| No. 1 chain tensioner assembly x Cylinder block sub-assembly
|
10
|
102
|
7
|
| Timing chain guide x Camshaft housing sub-assembly
|
21
|
214
|
15
|
FRONT CRANKSHAFT OIL SEAL
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
| Crankshaft pulley x Crankshaft
|
260
|
2651
|
192
|
REAR CRANKSHAFT OIL SEAL
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
| Drive plate and ring gear sub-assembly x Crankshaft
|
98
|
999
|
72
|
ENGINE ASSEMBLY
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
in.*lbf
|
| Engine mounting bracket RH x Cylinder block sub-assembly
|
54
|
551
|
40
|
|
| Engine mounting insulator LH x Front frame assembly
|
99
|
1010
|
73
|
|
| Engine mounting insulator RH x Front frame assembly
|
99
|
1010
|
73
|
|
| Front engine mounting insulator x Front frame assembly
|
58
|
591
|
43
|
|
| Engine mounting insulator LH x Automatic transaxle assembly
|
95
|
969
|
70
|
|
| Engine mounting insulator RH x Engine mounting bracket RH
|
95
|
969
|
70
|
|
| Front engine mounting insulator x Front engine mounting bracket
|
87
|
887
|
64
|
|
| Drive shaft bearing bracket x Cylinder block sub-assembly
|
64
|
653
|
47
|
|
| Frame side rail plates RH and LH x Vehicle body
|
Bolt (A)
|
85
|
867
|
63
|
|
| Bolt (B) and Nut (B)
|
32
|
326
|
24
|
|
| Front suspension member rear braces RH and LH x Vehicle body
|
Bolt (C)
|
85
|
867
|
63
|
|
| Bolt (D) and Nut (D)
|
32
|
326
|
24
|
|
| Engine moving control rod x Engine mounting bracket RH
|
38
|
387
|
28
|
|
| Engine moving control rod x Engine moving control rod bracket
|
52
|
530
|
38
|
|
| No. 2 engine mounting stay RH x Engine moving control rod bracket
|
38
|
387
|
28
|
|
| No. 2 engine mounting stay RH x Camshaft housing sub-assembly
|
38
|
387
|
28
|
|
| Air cleaner bracket x Battery carrier
|
8.0
|
82
|
|
71
|
| Engine wire x Engine room relay block
|
8.0
|
82
|
|
71
|
| Inlet air cleaner assembly x Vehicle body
|
7.0
|
71
|
|
62
|
| Air cleaner case sub-assembly x No. 2 air cleaner bracket
|
5.0
|
51
|
|
44
|
| Battery clamp x Vehicle body
|
Bolt
|
5.4
|
55
|
|
48
|
| Nut
|
5.4
|
55
|
|
48
|
| Positive (+) cable x Positive (+) battery terminal
|
5.4
|
55
|
|
48
|
| Negative (-) cable x Negative (-) battery terminal
|
5.4
|
55
|
|
48
|
ENGINE UNIT
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
in.*lbf
|
| Stud bolt x Stiffening crankcase assembly
|
Stud bolt (A)
|
9.5
|
97
|
|
84
|
| Stud bolt (B)
|
4.0
|
41
|
|
35
|
| Engine balancer assembly x Stiffening crankcase assembly
|
24
|
245
|
18
|
|
| Stiffening crankcase assembly x Cylinder block sub-assembly
|
Bolt (A)
|
24
|
245
|
18
|
|
| except Bolt (A)
|
43
|
438
|
32
|
|
| No. 1 oil pan baffle plate x Stiffening crankcase assembly
|
10
|
102
|
7
|
|
| Oil strainer sub-assembly x Stiffening crankcase assembly
|
9.0
|
92
|
|
80
|
| Oil pan sub-assembly x Stiffening crankcase assembly
|
10
|
102
|
7
|
|
| Oil pan drain plug x Oil pan sub-assembly
|
40
|
408
|
30
|
|
| Stud bolt x Camshaft housing sub-assembly
|
6.5
|
66
|
|
58
|
| Timing chain cover plate x Timing chain cover sub-assembly
|
10
|
102
|
7
|
|
| Timing chain cover tight plug x Timing chain cover sub-assembly
|
30
|
306
|
22
|
|
| Cylinder head cover sub-assembly x Camshaft housing sub-assembly
|
12
|
122
|
9
|
|
| Crankshaft pulley x Crankshaft
|
260
|
2651
|
192
|
|
| Water inlet housing x Cylinder block sub-assembly
|
43
|
438
|
32
|
|
| V-ribbed belt tensioner assembly x Water inlet housing
|
21
|
214
|
15
|
|
| No. 1 water by-pass pipe x Water inlet housing and Cylinder block sub-assembly
|
12
|
122
|
9
|
|
| Separator case x Ventilation case sub-assembly
|
10
|
102
|
7
|
|
| Ventilation case sub-assembly x Cylinder block sub-assembly
|
21
|
214
|
15
|
|
| Engine cover joint x Cylinder head cover sub-assembly and Camshaft housing sub-assembly
|
10
|
102
|
7
|
|
| Sensor wire x Cylinder block sub-assembly
|
21
|
214
|
15
|
|
| No. 1 compressor mounting bracket x Cylinder block sub-assembly and Stiffening crankcase assembly
|
21
|
214
|
15
|
|
| Engine oil level dipstick guide x Water inlet housing
|
10
|
102
|
7
|
|
| No. 1 engine hanger and No. 2 engine hanger x Cylinder head sub-assembly
|
43
|
438
|
32
|
|
CYLINDER HEAD
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
in.*lbf
|
| Stud bolt x Cylinder head sub-assembly
|
6.5
|
66
|
|
58
|
| No. 1 straight screw plug x Cylinder head sub-assembly
|
44
|
449
|
32
|
|
| No. 2 straight screw plug x Cylinder head sub-assembly
|
78
|
795
|
58
|
|
CYLINDER BLOCK
| Part Tightened
|
N*m
|
kgf*cm
|
ft.*lbf
|
in.*lbf
|
| Stud bolt x Cylinder block sub-assembly
|
Stud bolt (A)
|
6.5
|
66
|
|
58
|
| Stud bolt (B)
|
8.5
|
87
|
|
75
|
| No. 2 oil nozzle sub-assembly x Cylinder block sub-assembly
|
10
|
102
|
7
|
|
| No. 1 oil nozzle sub-assembly x Cylinder block sub-assembly
|
10
|
102
|
7
|
|
| Crankshaft bearing cap x Cylinder block sub-assembly
|
1st
|
20
|
204
|
15
|
|
| 2nd
|
40
|
408
|
30
|
|
| 3rd
|
Turn 90°
|
| Connecting rod cap x Connecting rod sub-assembly
|
1st
|
40
|
408
|
30
|
|
| 2nd
|
Turn 90°
|