Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › from 2018.09
RM3160E _53 Suspension _019690 REAR SUSPENSION _0109430 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48540 1.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C296521C01
1.063,2.542 1.469,2.813 1.469,2.813 1.719,2.813 true 1.75,2.719 2.01,2.906 0.26,0.188 10 false *a 1.417,0.583 1.625,0.802 0.208,0.219 10 true A 1.115,2.896 1.271,3.094 0.156,0.198 10 false B
*a Protector


Temporarily install the rear shock absorber assembly with the bolt (A), bolt (B) and nut.

NOTICE:
·

Ensure that the protector faces the front of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt (B) with the nut secured.

·

Fully tighten the bolts after stabilizing the suspension.




b.

Slowly lower the rear No. 2 suspension arm assembly.


Hide 2.STABILIZE SUSPENSION

a.
C293824C01
0.625,1.823 0.938,1.823 false 0.635,1.99 1.073,1.99 false 0.302,0.406 0.458,0.604 0.156,0.198 10 false A 0.458,1.719 0.615,1.917 0.156,0.198 10 false *a 0.469,1.896 0.625,2.104 0.156,0.208 10 false *b
*a Wooden Block
*b Jack
V100155

Wooden block placement location


Jack up the rear No. 2 suspension arm assembly, and place a wooden block underneath to avoid damage. Apply load to the suspension so that the rear upper control arm assembly is positioned as shown in the illustration.

Standard Length (A):

24.3 mm (0.957 in.)


CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.



HINT:

If the rear upper control arm assembly cannot be positioned as shown in the illustration even when the rear No. 2 suspension arm assembly is jacked up, apply additional load to the vehicle such as by placing a weight in the luggage compartment.



Hide 48540 3.INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C293823N02
1.406,0.583 1.573,0.833 0.167,0.25 10 true A 1.094,2.906 1.25,3.104 0.156,0.198 10 true B

Install the rear shock absorber assembly with the bolt (A) and bolt (B).

Torque:
Bolt (A) : 100 N*m (1020 kgf*cm, 74 ft.*lbf)
Bolt (B) : 92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt (B) with the nut secured.



Hide 4.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)