Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › from 2018.09
RM3160E _53 Suspension _019690 REAR SUSPENSION _0109431 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 48802 2.REMOVE REAR STABILIZER LINK SUB-ASSEMBLY

a.
C293825N01
1.885,1.635 2.042,1.833 0.156,0.198 10 true A 2.552,1.667 2.708,1.865 0.156,0.198 10 true A 2.531,0.781 2.688,0.979 0.156,0.198 10 true B

Remove the 2 nuts (A) and separate the rear stabilizer link sub-assembly from the rear No. 2 suspension arm assembly.


b.

Remove the nut (B) and the rear stabilizer link sub-assembly from the rear stabilizer bar.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48231B 3.REMOVE REAR COIL SPRING

a.
C293826C01
1.26,1.635 1.688,1.635 true 0.198,1.917 0.344,1.917 true 2.146,0.875 2.146,0.594 2.146,0.594 2.365,0.594 true 2.156,0.635 2.354,0.635 true 2.51,1.635 2.51,1.354 2.51,1.354 2.792,1.354 true 2.521,1.51 2.792,1.51 true 1.708,1.521 1.99,1.719 0.281,0.198 10 true *a 0.031,1.833 0.344,1.99 0.313,0.156 10 false *b 2.073,0.885 2.26,1.073 0.188,0.188 10 true *c 2.438,1.615 2.625,1.802 0.188,0.188 10 true *c 3.042,1.594 3.198,1.792 0.156,0.198 10 true A 0.229,1.583 0.385,1.781 0.156,0.198 10 true B
*a Wooden Block
*b Jack
*c Matchmark


Place matchmarks on the No. 2 adjust cam, toe adjust cam sub-assembly and rear suspension member sub-assembly.


b.

Support the rear No. 2 suspension arm assembly using a jack and wooden block.

CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.



c.

Loosen the nut (A).

NOTICE:

Do not remove the nut.



d.

Remove the bolt (B) and nut, and separate the rear No. 2 suspension arm assembly from the rear axle assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Slowly lower the rear No. 2 suspension arm assembly, and then remove the rear coil spring.


Hide 48259A 4.REMOVE REAR UPPER COIL SPRING INSULATOR

a.
C293827

Remove the rear upper coil spring insulator.


Hide 48258C 5.REMOVE REAR LOWER COIL SPRING INSULATOR

a.
C293828

Remove the rear lower coil spring insulator from the rear No. 2 suspension arm assembly.