Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2018.09
RM3160E _53 Suspension _060167 TIRE PRESSURE MONITORING _0296404 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
C361351C10
0.333,0.75 0.75,1 0.417,0.25 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.406,0.771 0.865,0.969 0.458,0.198 10 false M45
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the M45 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M45-1 (IG) - M45-12 (GND) Y - W-B IG power source Engine switch on (IG) 10 to 16 V
M45-7 (+B) - M45-12 (GND) V - W-B Power supply (from battery) Always 10 to 16 V
M45-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Connect the M45 tire pressure warning ECU and receiver connector.


c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


E129452C51
2,0.75 2.417,1 0.417,0.25 0.115,0.094 0.438,0.344 0.323,0.25 10 false *a 2.063,0.771 2.417,1.021 0.354,0.25 10 false M45
*a Component without harness connected
(Tire Pressure Warning ECU and Receiver)
- -


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M45-3 (CLSW) - M45-12 (GND) V - W-B Tire pressure warning reset switch
·

Engine switch on (IG)

·

Tire pressure warning reset switch on


Below 1.5 V
·

Engine switch on (IG)

·

Tire pressure warning reset switch off


8 to 15 V
M45-4 (RDA) - M45-12 (GND) LG - W-B Output signals Engine switch on (IG) Pulse generation (see waveform 1)
M45-5 (PRG) - M45-12 (GND) SB - W-B Input signals Engine switch on (IG) Pulse generation (see waveform 1)


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal M45-4 (RDA) -M45-12 (GND)
M45-5 (PRG) - M45-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Engine switch on (IG)

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.